Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

Where should I put the least worn tyre? on the front or the back? This is for XC MTB. Thanks in advance.

share|improve this question
    
In addition to the comments below, laziness is certainly a factor. Quite often the rear wears out before the front is showing any wear at all, and moving the front to the rear (for twice as much work) only slightly improves the tread on the front. –  Daniel R Hicks Sep 28 '12 at 0:42
add comment

5 Answers

up vote 19 down vote accepted

The Good or less worn tire should go on the front wheel as indicated in this Sheldon Brown Article on Tire Rotation

Although the article does hint to the fact that you should not be really rotating tires to the front wheel that may have been used on the rear wheel.

The only time tire rotation is appropriate on a bicycle is when you are replacing the rear tire. If you feel like taking the trouble, and use the same type of tire front and rear, you should move the front tire to the rear wheel, and install the new tire in front.

The reason for this is that the front tire is much more critical for safety than the rear, so you should have the more reliable tire on the front.

If you have a blowout, if it is on the rear tire, you have a very good chance of bringing the bike to a controlled stop. If your front tire blows, you can lose steering control, and a crash is a real possibility.

share|improve this answer
add comment

Place the less worn tire on the front. You need very little tread to achieve traction on the rear tire when climbing. Though counter intuitive, tire tread has very little impact on keeping your rear tire from slipping and spinning out on a climb. Maintaining traction is much more about torque, and weight and body positioning on the bike. I intentionally use a rear tire with low worn out center tread to reduce drag and increase rolling efficiency. Center tread on the rear tire may help keep the tail from bouncing and sliding around a bit, but this is not critical in maintaining control.

share|improve this answer
add comment

Very thoughtful considerations, especially directing the thinking towards MTB terrain given that so many folks drive to trails and might not worry about pavement wear and those safety concerns as much.

My knee-jerk reaction to the original question was a more superficial performance thought for a MTB:

If you rely on a knobby tread and encounter sloppy (muddy/wet) conditions with a worn-down rear tire and a newer front tire, you might be better served rotating the newer tire to the drive tire in the rear. It would have to be a pretty bald rear tire to make the swap noticeable though.

If I have two bald tires and only enough money for one tire, I'd definitely replace the back one first if the conditions are sloppy.

share|improve this answer
    
So with sloppy conditions and good traction provided by the single good-threaded tire on the rear, how does one HANDLE the bike with a bald front tire in the first place? –  heltonbiker Sep 30 '12 at 17:08
add comment

@MrDaniel has a very good answer, however if the bike is used XC MTB a blowout is less of a concern than handling when compared to a road bike, as MTB tires (in true off road conditions) loose performance as they loose tread, unlike a road tire. Your riding style and ground you ride will dictate to some extent what you do. If you have steep, slippery uphills and traction your most important problem, a better tread on the back helps. If control is your problem and you find the front a bit sketchy - then the new one on the front would be better.

If in doubt, don't loose any sleep over it - put it on either the one you are replacing (easy - only one tire change) or the front.

Don't forget that with MTB tires they are all quite different characteristics, build for particular combinations of riding conditions and tradeoffs. Some are designed specifically for back or front, or you change the rotation direction between front and back - therefore it is not as simple as just considering tread wear.

share|improve this answer
add comment

Generally you want the best tread on the front, as a front tire skid is much more dangerous than a rear tire skid.

However, I tend to ride my tires until the cord nearly shows, and, given that flats are about 5x more common on rear tires than front tires (and front-tire flats are much easier to fix), I'd be tempted to put the better tire on the rear, to reduce flat potential.

share|improve this answer
2  
+1 for a good argument in favor of a strategy contrary to the common practice. This might mean each rider must make the informed decision regarding what to do, instead of there being one right answer. (Now the rear-tire-flats-more-often theory would be a tough subject to debate... :oP) –  heltonbiker Sep 27 '12 at 22:04
    
@heltonbiker : Agree it's probably subjective - would live to see some hard numbers. Possibly an observation/reality caused by under inflated tires - the back carries more weight than the front and many riders put the same pressure in both. This means the back, being more likely to be under inflated, maybe more prone to snake-bite type punctures. I admit though thats is at best a thesis with no facts to back it up.... –  mattnz Sep 29 '12 at 5:32
    
I think the back punctures occur more often primarily because steering with the front "scrubs" it, so something that attaches to the front tire doesn't stick to it very well, whereas on the back the "something" will stay there for hundreds of revolutions, working its way into the tread. And of course there's more weight on the back tire, so objects are forced through it more rapidly. (And there's always the fact that nature is perverse and wants to puncture the back tire because it's so much harder/messier to change.) –  Daniel R Hicks Sep 29 '12 at 12:30
    
A simpler explanation is that worn tires are more likely to puncture, the back wears faster than the front so most of the time the back is more worn than the front and so is more likely to puncture. I'm sure there are other contributing factors but this seems to be the most likely cause. –  swl10-speed Oct 3 '12 at 7:26
    
@swl10-speed - My first back tire puncture with my current bike occurred on its test ride. –  Daniel R Hicks Oct 3 '12 at 11:43
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.