Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I have a hybrid bike which has dropped handlebars with Shimano Tiagra dual brake/gear levers. The front mech is a Tiagra triple ring and the back mech is Shimano Deore XT (9 sprockets) I have developed back problems and now need a more upright position when riding and am hoping to convert my bike to a flatbar. Can anyone help in identifying the options for compatible Gear Shifters. Thanks in advance

share|improve this question
add comment

3 Answers

As long as your choosing a 9 speed Shimano shifter for the rear and triple shifter for the front you'll be fine. That's basically everything in the Deore lineup, as long as it's 9 speed. Obviously you'll want to stay away from 10 speed shifters and dont try to mix and match Shimano derailleurs and SRAM shifters or vice versa.

Though you didn't ask this, what may be a more important concern is how your bike is going to fit when you slap flat bars on it. Road bike frames are shorter in the effective top tube than mountain bikes are due to the fact that a straight handlebar decreases reach compared to a drop bar. Your bike is going to fit pretty darned short if you do a flat bar conversion which can cause comfort problems of it's own. There are other fit issues to be considered when doing a flat bar conversion on a road bike, but in my opinion this is the big one.

share|improve this answer
    
Thank, but I.m hoping to replicate the measurement of my old mountain bike which is extremely comfortable and "pain free" –  Brian Jan 11 '13 at 15:19
    
Just make sure that you replicate the length of the entire cockpit- it will likely require a very long stem. –  joelmdev Jan 11 '13 at 18:09
    
I will do, thanks for the advice –  Brian Jan 12 '13 at 9:41
add comment

Before you rush to spend money on different bars and different shifters, have you ever considered a shorter stem? Perhaps a photo of your current bars/stem, and/or an actual measurement of your stem would help me to be more specific. You should measure it center-to-center, as shown in the illustration (3).

Stem measurements

What I've found is that I get back pain when I'm too stretched out. That is, when the reach is too much for me, I get back pain. You can see the measurement I'm referring to in the picture below.

Bicycle Reach

It doesn't take much of a change in the stem length to make a difference. Long story short, I changed my saddle and my bars, and started getting horrible back pain after 40 miles or so. I shortened my stem by 30 mm, and all is well. I can ride 70 miles or more before I start feeling any pains, but back pain is not one of them, typically.

If you can't post pics of your bike, measurements would be helpful for you to know. In addition, check your bike vs. a fit calculator like this one. Make sure you're in the range of numbers before you start throwing money at this problem.

share|improve this answer
    
Thanks but I had already tried this option without much success. my intention was to try and replicate the measurements of my mountain bike which i can ride on for hours. –  Brian Jan 11 '13 at 15:14
add comment

Nine speed Shimano mountain bike shifters are usually (maybe always) compatible with Shimano derailleurs. I've definitely mismatched them in a variety of configurations and never had a problem. Stick with Shimano and you should be fine.

share|improve this answer
3  
Be careful, 10 speed shimano road and mountain drivetrains may not be compatible since they changed cable pull ratios for 10 speed Dyna-sys mountain bike drivetrains. 9-speed is generally ok to mix and match. –  Benzo Jan 10 '13 at 23:03
    
Thanks, @Benzo. The OP said it was 9 speed so I didn't clarify. But I probably should have so I fixed the answer. –  jimirings Jan 11 '13 at 15:17
    
Thanks I had hoped that Shimano 3 x 9 shifters would work but I didnt want to lay out for the expensive Tiagra shifters if I could find a cheaper (down the range) alternative, –  Brian Jan 11 '13 at 15:17
1  
Tiagra is specific to the road line. The standard Shimano mountain bike shifters are, from lowest to highest quality: Alivio, Deore, LX, XT, and XTR. There are a couple of others that are marketed for specific niche purposes, e.g., downhill. shimano.com –  jimirings Jan 11 '13 at 15:24
    
Thanks, I'm going to try and find Deore XT shifters which hopefully should be compatible –  Brian Jan 12 '13 at 9:42
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.