Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I like to ride with a hydration pack when I mountain bike in the winter since all sorts of nasty stuff gets tossed up at my bottles. However, I've had issues with the tube or valve getting clogged due to the water inside freezing during rides in the low 20s. It's really hard to deal with this issue while you're out in the woods.

Is there anything I can do to prevent this from freezing so quickly?

share|improve this question
5  
Alcohol is a pretty good antifreeze. ;) –  Daniel R Hicks Mar 6 '13 at 22:55
    
I would also consider purchasing a hydration pack made for snowboarding / backcountry skiing. Camelbak and Salomon make these and typically have insulated hose or are made to be low profile and fit under a jacket. –  Benzo Oct 28 '13 at 17:10

4 Answers 4

up vote 9 down vote accepted

I see snowboarders with an insulating cover over the tube. If that doesn't provide enough insulation, I've worn my pack under my jacket leaving the entire pack, tube and bite valve covered and insulated.

Here is a 3 foot Hydration Pack Insulated Drink Tube Cover on amazon for $7 US

share|improve this answer
    
What's the deal with the rads.stackoverflow redirect link? –  jimirings Mar 7 '13 at 0:03
    
No idea, I put in direct link to amazon, maybe StackOverflow is detecting and adjusting for the affiliate referral. –  Glenn Gervais Mar 7 '13 at 0:27
1  
@jimirings meta.stackexchange.com/questions/26964/… –  Kevin Reid Mar 7 '13 at 2:09
    
@KevinReid Cool! Thanks! –  jimirings Mar 7 '13 at 2:13
    
I can vouch for putting the tube under the jacket as well. It's the only thing that keeps the water flowing when it gets really cold. I have an insulated tube, but it simply doesn't work when it gets down to -20 °C/-4 °F. –  user1049697 Oct 20 '13 at 12:38

The trick is to blow the water back up the tube and into the reservoir right after you take a drink. This will keep your tube and bite valve from freezing. This works well even at well below freezing temperatures when skiing.

share|improve this answer
1  
Between blowing into the tube when done, wearing the pack under your coat and getting an insulated tube cover, you should be set. –  Chef Flambe Mar 11 '13 at 23:23

The tube has a lot of surface area and not a lot of volume, so it's going to lose heat quickly compared to the reservoir. In addition to insulating the tube mentioned by Glenn Gervais you can start with hot water in the reservoir and frequently drink a little bit to keep reheating the tube. This Nordic skiing article discusses this technique in more detail.

You could also try a Nordic skiing water bottle holder like the one in this (5 part!) article. I've noticed while skiing that a horizontal bottle seems stay ice free at the valve longer. In a vertical holder, turning the bottle upside down also helps.

I've never tried this, but you might also try to keep the water in the reservoir warm by attaching a chemical hand/foot warmer to the outside of the bag. Test it first to check that it won't damage the plastic bag, though I wouldn't expect something made to keep near your skin would get hot enough. Don't put it in the bag though. If it leaks it's probably dangerous to your health.

share|improve this answer
2  
I used the warm (not hot) water and frequent drinks when mountain climbing, with a insulation cover to extend time between drinks, with great success. Most chemical warmers are Sodium acetate - which is used as a food additive, and has a melting point of 55C - so it won't hurt the drink bladder –  mattnz Mar 7 '13 at 3:18

Some hydration packs (such as Source Hydration Systems) have a wider diameter than others and/or an insulated tube cover. Both of those can help keep water from freezing in the tube.

Disclaimer: I am associated with Source Hydration Systems.

share|improve this answer
    
If you're affiliated with Source Hydration Systems in any way, you need to make that extremely clear. Second, you seem to have a lot of stuff in this answer that doesn't really address the question. –  freiheit Oct 20 '13 at 20:55

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.