Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I tend to ride relatively modest gear (Tiagra/Ultegra), but when I'm riding near higher-end bikes, I sometimes notice that the clicking sound that comes from their cassette/free-wheel while coasting seems to be much louder and more distinct than on my bike. Why is this? Intuitively, one would expect that a quieter drive-train would be an indicator of greater efficiency, but that doesn't seem to be the case here. Is it something to do with different construction, or materials? Can you get 'quiet' high-end cassettes, or is being noisy while coasting the price you must pay for being efficient while peddling?

share|improve this question
    
I don't know of any correlation between the quality of cassettes and the noice they make, but silent ones certainly are available. sheldonbrown.com/gloss_ri-z.html#rollerclutch –  jimirings Apr 16 '13 at 18:58
1  
I wouldn't call Ultegra particularly modest, the only range better is Dura –  PeteH Apr 16 '13 at 20:12
2  
It's important to note that the freewheel is part of the hub, and while you might have some or mostly Ultegra parts, many bikes are sold with parts that aren't all from the same groupset. When you say the cassette is loud, what you're actually saying is that the freehub is loud, at least when talking about higher end bikes. Low end bikes typically have a freewheel built into the cassette. –  Kibbee Apr 16 '13 at 20:43
1  
Loudness in the freehub/freebody is usually due to the very light oil used to lubricate the inner parts. Thicker oil can be used to lessen the noise and even grease in some cases, but it's high viscosity is pointed at for not being so efficient. –  Jahaziel Apr 16 '13 at 20:53
2  
youtube.com/watch?v=SG0uBDvgXu0 Noisy freehubs are definitely a design thing. I don't get it. –  WTHarper Apr 17 '13 at 0:05

3 Answers 3

up vote 11 down vote accepted

Most of the noise comes from pawls on the freewheel hitting against the splines on the engagment surfaces which makes up the racheting unit.

Some reasons for the noise between freewheels?

  • Tension on pawls could be higher causing more noise as they glide over the engagment surfaces

  • High end freewheels have more pawls and engagement points than lower end freewheels, so there are more ridges in the engagement surface and more pawls hitting the splines on the engagement surface. The reason this is desirable is that more pawls and engagement points means faster engagement when you start pedaling.

  • Different grease (or less grease) could also be used inside higher end freewheels that is less viscous and provides less resistance, allowing the spring action of the pawls to cause more noise as they float over the the splines on the engagement surface since they are less restricted by the grease.

    Of course there are exceptions to these. Some hubs don't use your standard racheting mechanism and use a 'roller clutch' instead. The roller clutches tend to be very quiet, but are more prone to failure.Here's a good description of how those work. http://pardo.net/bike/pic/mobi/d.winners-hub/index.html

  • share|improve this answer
        
    Great answer. I would like to mention that more points of engagement become particularly using with mountain bikes -- especially when ascending a technical section in a very small gear. I personally don't see the need on the road. –  Paul H Sep 10 at 15:56

    I think loudness is not a good indication of efficiency, since loudness (and pitch as well) can be affected by many more factors at same or similar total energy consumption.

    share|improve this answer

    I had deore xt hubs on my mtn bike, they were silent. I have rebranded Formula on my 2008 Bontrager Race Lites which have a nice clicky sound. Upon servicing I must have put too much grease in and it muted the sound. So perhaps there is a relationship between sound and pawl wear. I have DT Swiss star ratchet on my mtn bike now and they have an excellent sound IMO. Chris king hubs have a legendary sound, describe by customer quote "It rolls good with angry bee sound"

    share|improve this answer
        
    I seem to recall reading that Shimano designs their hubs to be quiet. Or perhaps it's that their hub design is inherently quieter. Something like that. –  Paul H Sep 10 at 15:58

    Your Answer

     
    discard

    By posting your answer, you agree to the privacy policy and terms of service.

    Not the answer you're looking for? Browse other questions tagged or ask your own question.