Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I want to tweak my gears, from time to time: Adjust my front and rear derailleur limits, see if the shifts are smooth, make small adjustments on the cable tension, and so on.

Is there any way to get the bike in position without help of anyone?

I don't want to spend money on a bike stand.

share|improve this question
1  
What exactly do you mean by "tweak my gears"? –  amcnabb Jun 5 '13 at 23:35
    
Adjusting my front and rear derailleur limits, see if the shifts are smooth, small adjustments on the cable tension... –  danieltorres Jun 5 '13 at 23:41
    
Just hang the front of the seat on any convenient "peg", or rig hooks or a rope to suspend the bike from. All you need to do is somehow get the rear wheel off the ground while having the pedals clear to turn. –  Daniel R Hicks Jun 6 '13 at 0:39
6  
possible duplicate of Alternatives to buying a repair stand? –  Neil Fein Jun 6 '13 at 0:55
    
I used to ride with a guy that would bend over and hang the seat on his neck for quick roadside adjustment. I'm not sure my neck is up to the task, so I used to hang the bike seat on a a hook that hangs from the ceiling, but finally bought a workstand which is far superior. –  Johnny Jun 6 '13 at 1:27

8 Answers 8

up vote 10 down vote accepted

In my experience, most light work can be done with the bike stored upside down (standing on the handlebars and seat). Of course, I'm assuming that you're talking about a road bike. Other bikes, like a mountainbike with a twist-shifters or trigger-shifting, might not be as well suited.

share|improve this answer
    
+1) Although its far from ideal, I consider it a last resort - if my MTB 'breaks' when in the field it is often the easiest solution. –  mattnz Jun 6 '13 at 4:11

Before I bought a bike stand, I used the bike rack on my car. I still use it in a pinch.

share|improve this answer
    
There is some issue with this - if you have a bike rack which is a trailer hitch mount or spare wheel mount then this is possibly OK but if you have a trunk rack, you have to be careful not to get dirt on the pads which touch the car (lest you scratch the paint on your car). –  Batman Dec 3 at 19:05

I have double kickstand on the bike which can act as mini repair stand. I pull the bike on the kickstand, and put some weight (u-lock and chain) on the front of the bike so it tilts forward and back wheel gets lifted in the air.

share|improve this answer

I have two large hooks attached to my basement ceiling. I attach a 1 inch cargo strap (look for them in camping supplies) from the hook to my saddle and a second around the bars and stem. This suspends the bike while allowing the wheels and crank to spin freely. By adjusting the strap length I can position the bike so the area being worked on is close to eye level. The hooks were less than $3 and the straps were $3 each.

share|improve this answer
    
That's a cheap solution but the bike would tend to swing to and fro. I would find it hard to work on a bike that would move when touched. –  Carey Gregory Jun 6 '13 at 3:50

A cheap solution is a wall-mounted bike holding stand. The simple ones are just a couple of prongs that stick out from the wall and support the top tube of your bike. Something like this is $US40 or you can get fancy with this (will work better with sloping top tubes)

I suspect you could build one out of a 1.5m length of timber and some screws quite easily, although attaching it to the wall would require a little care.

The rope-based hanging bike storage systems also work well for this if you can put up with the bike swinging round. Those allow better access, but the bike moves. A solid wall mount won't move but you have to take the bike down and flip it round to access the other side, and you can't turn the handlebars much.

share|improve this answer

Normal workbenches have these big clamp tools attached to the border of the bench. LINK TO IMG

You can turn your bicycle upside down and carefully clamp the top tube. I use rags to protect the frame. The bicycle is as stable as it can get.

EDIT* This method should only be used on steel frames and with great care. Also keep in mind that high quality steel frames are 'butted' (thinner in the middle).

share|improve this answer
1  
I'd only do this on a steel frame, and even then one must be careful to not crush the tube. Remember, better quality frame tubes are "butted" and thinner in the middle than at the ends. –  Daniel R Hicks Jun 6 '13 at 10:22

Turn the bike upside down and clamp the handle bar stem in the jaws of a WorkMate workbench and rest the seat on the opposite end of the WorkMate work surface. Turning the seat around backwards on its stem may be helpful.

share|improve this answer

Here is a cheap ($20) bike stand that elevates the rear wheel: http://www.amazon.com/Sunlite-Bracket-Bicycle-Display-Stand/dp/B000C17HJ4

Note that it works best with thinner-tubed steel bikes, and doesn't necessarily hold up a bike with a thick aluminum downtube optimally.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.