Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I have been working my way through issues with noisy front cantilever brakes. After running through many different ways to solve the issue including new pads (Kool Stop Dura2 Duel Compound), setting the toe in and cleaning the rims. I now believe the noise is being generated by the play in the pivot point of the cantilever arm. It is not possible to tighten the bolt any further so there will need to be a washer or shim placed in here.

Has anyone had any success in removing the play from the pivot point?

The bike is a cyclocross Kona Jake 2012.

share|improve this question
    
I'm skeptical that the "play" you're seeing is causing the noise. If the bushings are worn such that the arm "rocks" on the pin, that would be bad, but sliding on the pin should not be a problem. Nonetheless, most hardware stores have a drawer full of "shim washers" in various sizes, and you likely can find some that will fit and reduce the distance the arm can slide up/down. –  Daniel R Hicks Jul 15 '13 at 14:40
    
Thanks! I am still not sure what is causing the noise, but I have got a setup so it's not been generated unless I really slam on the brakes. –  Andy Clark Jul 15 '13 at 19:08
    
I have gone with extreme toe in the brake pads. It has only started happening and since the pivot point is the connecting point of the brakes to the forks, I figured that the play there might contribute to the shudder and the noise. The headset and all other connections are tight. I will know more after tomorrows commute. –  Andy Clark Jul 15 '13 at 19:28
    
It should be noted that a certain amount of brake noise, while not inevitable, is quite common. I don't let it bug me if I get a little squeal when braking hard. –  Daniel R Hicks Jul 15 '13 at 22:44
    
Some bikes have removable pivots. If yours are worn, you could replace them. Wear in the brake bushing is more likely though. If you mean the pivot is flexing under load, you could use an old-style brake booster. –  armb Jul 17 '13 at 9:29

1 Answer 1

Before I add my two cents here I'll mention that this post is rather old to be unanswered. If you figured this out already write an answer and choose it as "the answer" so it doesn't show up as unanswered and others can learn from it.

So, by "play" you could mean front to back (as in the length of the post/bolt) or around the bushing (as in a difference in the diameter of the post and hole in the brake arm).

I just checked the oldest canti-brake bike I've got (from the 1980s) and there is no play in either sense described above. So I would attempt to solve that problem next as the things you've already tried are all good, especially your choice of pads. You might want to try the salmon colored rather than the dual compound though. They are the better of the two compounds for braking but they wear out faster.

If it is the former type of play I agree with the advice of @Daniel R Hicks. If it is the other and you don't have replaceable canti-studs you ought to replace the brakes (arms) themselves. If there is play when they are at rest they will shimmy and shudder when braking. If there is play due to the strength of fork then you need a brake booster as suggested by @armb.

Another question for you - are both the brakes and levers original to the bike or have you replaced either? Mixing canti and v-brake components will cause problems but I haven't heard of noise being one of them.

A final note - take heart! I have a friend who is a fanatic about bike maintenance. He was a bike mechanic, but now is an engineer in aerospace and his bike stuff is rather high end. Last year he adjusted and replaced everything and never found the source of the noise. He replaced the bike instead!

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.