When a person sits on a bike, the air pressure in the tires must go up because of the additional weight. With 100 PSI in 700x23 tires on a riderless bike, what is the air pressure when a 100 lb rider is sitting on the bike? A 200 lb rider?
An alternative way to calculate the solution:
The pressure in the tyre is 100psi. Pressure equals force divided by area. The surface area inside the inner tube (for a 700x23c tyre) is (very) roughly 7.2cm x 210cm = 1512cm square [or in square inches = 234insq]. The total forces involved on an unladen wheel are therefore 100 ‘pounds per square inch’ x 234 square inches = 23400 ‘pounds’. By sitting on the bike, one adds another 100 pounds to the wheel and thus to the forces, ie 23500 ‘pounds’. Assuming the inner tube does not change surface area ie the wall in contact with the ground is deformed in shape but overall not stretched or shortened, then the final pressure will be 23500 ’pounds’ divided by 234insq = 100.4 psi. Overall an increase in pressure by 0.4%.
I have used different assumptions/ approximations to previous posts:
All the deformation where the tire is in contact with the ground is NOT space lost.
If I push in a perfectly round balloon it will deform to a different shape. The volume in the balloon will go down and the pressure up. But the decrease in volume is far less then the volume displaced by my hand. Yes a balloon is elastic and will expand. This is true for even an inelastic balloon.
Under no load a tire is round. This is not by chance. The tire has a fixed amount of material. The tire will assume a shape that creates the largest volume for a fixed amount of material - a circle. Under the operating range we are examining the circumference of the tire does not change - the tire does not stretch.
Under load the tire deforms to a different shape - an ellipse.
The equation volume for the of a circle is:
Assume under load the tire displaces to r2 = 2r1 at the point of maximum displacement.
So roughly a 10% loss of volume at the point of maximum displacement.
For r2 = 2 r1 the length of the patch with the ground is about 2 r
On a 700 / 25
( 50*17/18 + (700π - 50) ) / 700π
Pressure increases inversely to volume
Lets look at a patch of 50mm X 25mm
I realize I Moz looks at it from all the displacement is lost.
I'm sure it's possible to calculate this but my bike was only a few steps away so it seemed easier to just measure the pressure change. I connected a floor pump with a pressure gauge and pumped the back tire to 100 psi on a 700x23 tire. I then sat on the saddle and watched the pressure gauge. It didn't move. I stood up and tried a second time with the same result. I'm sure it changed a bit but it was less than the resolution of the basic pressure gauge on my pump. Or maybe it was just a lousy experimental design.
I weight about 180 pounds.
So, experimentally with two trials, the answer is the pressure doesn't change very much.
As a first approximation you could use zero.
But more accurately, with a 23mm tyre you probably have about 20mm diameter of air inside. A 700c wheel is ISO 622, so has an inner radius of 311mm. So your tube forms a torus with major radius 321 and minor radius 10mm. A litre is a cubic decimetre (a cube 1/10th of a metre or 10 cm on a side) so it's easier to use dm for this. So, major radius = 3.21dm, minor = 0.1dm.
Now, at 100psi with a 200lb rider the flattened area is 2 square inches, or 1290 mm². So we want the volume of a toroidal section having that flat area. Conveniently the section is an ellipse, so the area is π (major radius)(minor radius) (and a circle is πr² because both radii are the same). As a first approximation let's say that the minor axis is half the width of the tyre (so 10mm) and see what happens:
That seems a little on the short side, but it's vaguely plausible, so what's the volume? Unfortunately the volume of a toroidal section is a bit beyond my rusty calculus, so I'm going to cheat. A lot.
First, what arc does this represent?
That's about 3.5° each side of the centre of the flat spot.
How deep is it? Since sine X = x for small x, and we definitely have small x, if we go out 20.5mm from the centre of the flat spot we've got a right triangle 20.5mm on the long side. The short side is that times sine 3.5° as above:
As you can see that's a pretty flat shape, so even a crude pyramidal approximation is not going to matter too much (if it's out by a factor of 5 or 10 it's not really going to matter, it's still going to be "roughly zero" as a fraction of the total volume above).
Conveniently we can express the volume of a pyramid as a factor of the area of the base:
The area from above was 1290 mm², which we need to divide by 100² to get it in dm² for the volume calculations = 0.129 dm²
What fraction of the original volume is this?
See, even if that's out by a factor of ten, we're still looking at a volume change of 10-5. So the pressure change will be about the same, a change of 1/1,000,000 the actual pressure.
If this was the XKCD guy's "What If" I'd now work out how fat you'd have to be to cause an appreciable change in tyre volume. But I'm not, so I shan't.
There's a very simple way to accurately estimate this: use Boyle's gas law which states that the product of pressure and volume is constant. Thus if the air volume in your tire decreases by 10% (which I think is a huge overestimate), then the new volume V2 is 0.9 times the old volume V1. Hence the new pressure P2 must be 1/0.9 = 1.11 times the old pressure, i.e. pressure increased by 11%. I'd conclude that pressure is barely affected by the weight of the person, if the tire has enough pressure to support you in the first place.