Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

The title says it all really. I've taken the front wheel off my mountain bike to get it in my car. When I get it out and try and put the front wheel back on the space between the brake pads isn't wide enough for the rotor. Whoops! I must have pulled the front brake.

How can I separate the the pads without damaging them?

EDIT

I have hydraulic disc brakes

share|improve this question
    
Do you mean that the brake pads are stuck together? –  sixtyfootersdude Jan 18 '11 at 11:58
    
No, there is a gap between them, just not enough for the rotor –  Phil Hale Jan 18 '11 at 12:46
    
Can you use an American Express card? –  Jay Bazuzi Jan 18 '11 at 17:55
1  
I've been jitteringly wondering this ever since I bought my first bike with hydraulic discs, six months ago... thank you for asking! –  DC_CARR Jan 20 '11 at 23:19

5 Answers 5

up vote 13 down vote accepted

As mentioned try a blunt bladed instrument (A large flat blade screwdriver will do) to pry the pads back in. Just put the screwdriver between the pads and lever the pads apart evenly! Just be carful though as sometimes the pistons that push the pads out can come out too far resulting in the pistons being slighly out of line, however if the pads have plenty of material left on them you should be fine to just lever them back in with the screwdriver, ther will be some resistance as you will also be pushing against the pistons and fluid pressure.

share|improve this answer
2  
Don't scratch the pads or they'll have to reset on the rotor surface. –  infamouse Jan 21 '11 at 20:27
1  
@infamous - Contaminating them from a dirty tool is a much more common problem than scratches. They are a bit tougher than the likes of a camera lens after all. –  mattnz Sep 4 '12 at 5:11
    
The amount of sand and general dirt I subject my brakes to suggests a dirty screwdriver won't make much of a difference. –  jurgemaister Sep 5 '12 at 14:03

Not as practical as some of the other solutions, but if you know a car guy, they've probably got brake pad spreaders laying around. You should be able to get an edge or corner far enough in to use them.

share|improve this answer

I just had to look this up for a friend, who accidentally completely closed them.

The recommended way, taken from "Zinn and the art of Mountain Bike Maintenance" is as follows. "Sometimes the pads in hydraulic disc brakes can rub because the pistons get pushed out too far, especially if the lever is applied without a rotor or spacer between the pads. You will have to push the pistons back in, usually by removing the pads and pushing the pistons back in with a plastic tire lever. On Hayes, the only thing pulling the pistons back in is the reversal of the twist the pistons apply to square-cross-section o-ring seals surrounding the waist of each piston, so the pistons tend to stay out too far once there. Pull out the pads, carefully push the pistons back in with the box end of a 10mm wrench(avoid pressing on the pin sticking out of the piston, which hooks the wire catch on the back of the pad), and replace the pad"

share|improve this answer

I've used a (clean) drywall putty knife. The blade is wider than a screwdriver, so there's less chance of gouging the pads. Slide the knife in between the pads, twist and pry a bit, and they open right up.

share|improve this answer

You could try blowing them with air to remove any dust particle that may prevent them for separating completely. If that's not enough you can use a "flat" screwdriver. When you have the screwdriver between the pads turn it carefully not to damage the brake pads and separate them a little bit.

share|improve this answer

protected by Community Sep 21 '12 at 5:39

Thank you for your interest in this question. Because it has attracted low-quality answers, posting an answer now requires 10 reputation on this site.

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged or ask your own question.