Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I just purchased a kid trailer to convert as a utility trailer. I paid $75 for it used. I could not find a cargo trailer for under $200 plus shipping (probably large). The trailer is also rated up to 100 pounds (which is actually more than the cargo trailer 75 pounds).

I was wonder if anyone had converted a kid trailer to a cargo trailer before and what the best way to do it is.

The frame is:

  • 2 Feet Wide
  • 30 Inches Long

Here are some pictures: enter image description here enter image description here

(Note: my trailer does not have the bar or wheel shown in the picture). enter image description here

Update: I have removed the fabric from the trailer to get a better look at the frame. The fabric is still in tact so it would be possible to put it back on the trailer.
enter image description here enter image description here

share|improve this question
1  
I've seen that type of kid trailer used for cargo as-is. As you noted, it's rated for a decent amount of weight. The cover should be handy for keeping rain and wind off your cargo, so you can more often just toss stuff in without separately securing it. –  freiheit Apr 10 '11 at 17:13
4  
Step 1: remove the kids. Step 2: add some cargo. Voila - you've got yourself a cargo trailer. As an added bonus, drivers will think that you're carrying kids, so they'll give you more space. –  Mike Baranczak Apr 11 '11 at 2:02
1  
Yeah. Agree with both @Mike and @freiheit. I bought one of these at a thrift store years ago and used it as-was to haul everything from groceries to a lawnmower (with the sides removed, of course). When the fabric finally gives up the ghost, then you might consider trying to build something else. If you plan to regularly haul piles of sharp objects, you should disregard my advice. Otherwise, why waste perfectly good and fitted fabric? It's certainly LIGHTER than anything you might build (assuming that you don't weld titanium in your living room). –  DC_CARR Apr 11 '11 at 19:06
    
Worth noting... the trailer that I mentioned before worked as a grocery-and-thrift-store truck for a little more than four years before the fabric started to tear through. We used it primarily for groceries, though I did mention the mower... sometimes bike parts... used it to haul a folding bike to and from the train station when friends came into town... etc. Lasted quite a while that way. –  DC_CARR Apr 11 '11 at 22:57
add comment

3 Answers 3

I made a infant-carrier conversion that also will work as a grocery getter. I found a plastic Sterilite bin that fit inside the trailer (just brushes the front and rear bar, about 1-2" from the sides). I cut the bin down to 6" tall, and drilled holes on each side for industrial strength zip ties, to connect to the frame tubes. The sterilite bin sits on the fabric bottom, but is suspended by the cable ties on 4 sides, in 2 places for each side. A used carseat for infants is ziptied to the sterilite bin. If I remove the baby seat, it serves as a cargo trailer.

enter image description here

Here is a photo of the plastic bin. (The fabric is removed for illustration)

share|improve this answer
    
Welcome to the site. (Have edited your post so the image shows up inline.) Looks like a great trailer hack for cargo, but I'm not sure attaching a child seat in this manner is safe. (I'd be concerned about it if it were my child.) –  Neil Fein Jul 8 '11 at 19:26
1  
I think I'd want some sort of straps wrapped round the bars and passing under the Sterilite bin, to give it some support (the cable ties could still serve to keep the bin in place). I'd probably also want some sort of straps attaching the baby carrier to the bin, and some more over the top to replace the seat belt which would hold it in place on a car seat. –  Amos Jul 8 '11 at 23:21
add comment

I would cut a bit of 10mm or 12mm plywood to fit underneath of the main frame section and use cable ties to hold it onto the frame. Probably at the level of that bar across the back of the trailer. That gives you a lip around the platform as well as a very slightly lower centre of gravity. Having lots of cut-outs where things are attached to the button of the frame isn't too much of a problem.

Ideally you'd find a plastic bin that exactly fit into the space but that's very unlikely to be possible. You will most likely find that the bin you get either sits too low and scrapes on the ground, or is too small on one side to work properly. If you go this route I suggest getting one the right width to sit on the main frame members and not worrying too much about how long it is. Having two bins next to each other might also work.

I think keeping the cloth cover will be handy, it will help keep your load in place as well as giving you some shelter from light rain.

Be aware that kiddy trailer load ratings are not the same as cargo trailer load ratings. No-one is expected to add exactly the load rating of children (look, it holds 2.3 children!), and people tend to be more gentle with children than with cargo. So a 30kg cargo trailer will probably hold the same weight as a 50kg rated kiddie trailer before it starts falling apart.

The reason they cost so much is that people won't buy a cheap, heavy, solid trailer. Instead they buy cheap, light, flimsy trailers and wonder why they fall apart. I built 12 of the heavy style and it took more than a year to sell them even though they cost the same as the flimsy junk ones. That as an educational experience for me.

share|improve this answer
    
Wow! Those are some great trailers you have there. If I lived down under I would defiantly buy one from you. I was not sure how useful a trailer would be so I thought that I would buy and convert a cheap one first. After I have tried it out (and figured out where it breaks) I think I may try to make my own. –  sixtyfootersdude Apr 11 '11 at 1:26
    
I hope they're easy enough to build from my plans and descriptions. I suggest making it to take one front and one rear wheel off a kids bike, rather than two front wheels like the mass trailers did. That way if/when you trash the wheels by overloading them you can just grab a discarded kids bike and get a new pair of wheels. I bought new wheels wholesale for the mass trailers but for one-off projects I use second hand bits. The kids bike also provides the extra tubing for that trailer. –  Мסž Apr 11 '11 at 1:41
    
FWIW, any welder will do for the trailer. You'd need to add gussets fore and aft each wheel if you were bolting it together, but I think you'd struggle with the towing arm and hitch area if you can't get access to a welder. –  Мסž Apr 11 '11 at 1:43
    
I have to agree. The hardest part is probably the towing arm (including the hitch). Can I ask you how much you had to pay the welder to make your trailers? –  sixtyfootersdude Apr 11 '11 at 2:05
1  
$50/hr - $350 for 12. But he's a friend so I'm not sure whether that's a full commercial rate. I suspect it depends on how easy you make it for him to do the job. If everything was cut and you had a clear one-page plan of the finished trailer so it was all straightforward it should be pretty cheap - less than half an hours work. –  Мסž Apr 11 '11 at 2:17
add comment

Strip the textile parts off, check the construction of the frame.

If the frame is a rectangle, put a fitting plastic bin / tub from home depot inside the rectangle.

If the frame is interspersed with beams, put a platform on top and put a bin / tub on top of that. Or maybe just a short railing like the one on croozer cargo.

You want to have the center of gravity as low as possible.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.