Take the 2-minute tour ×
Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It's 100% free, no registration required.

I do not have a chain whip or sprocket ring tool. Is it possible to change the rear sprocket without these tools?

share|improve this question
add comment

5 Answers

up vote 1 down vote accepted

To complete jm2's advice : you'll need the lockring tool. You could borrow it to your friend or go to your local bicycle workshop.

There is indeed an "ingenious technique" I've successfully used to screw the sprocket without using any chainwhip : use your chain ! It has been described here by guys from Milano, I assume you can use it to unscrew your sprocket :

share|improve this answer
add comment

I've heard of people doing it with a hammer and a screwdriver. It's not the best idea though. It won't be easy, and you'll foul the lockring and your cog's teeth.

Just plonk down the $20 on getting the proper tools for the job.

share|improve this answer
    
I'll be honest I cannot find these that cheap especially the lockring tool. I'm a cyclist in the UK :S –  will Feb 2 '12 at 17:07
    
@will, in general the UK isn't a back water when it comes to tools. For a standard cassette lock ring tool you can spend anywhere from £4 to nearly £20 depending on the quality and the mark-up at the shop. I'm not sure exactly which tool you need for a fixed gear sprocket though otherwise I'd try to answer your question more directly. This search might help though, chainreactioncycles.com/SearchResults.aspx?Search=lockring. They are usually a good option for the uk, especially on a budget. –  Colin Newell Feb 2 '12 at 20:34
    
I will need a lock ring tool and chain whip :) however I've noticed some lockrings have the notches within the ring rather than the outside... –  will Feb 3 '12 at 9:46
add comment

For the lockring a hammer and screwdriver works sometimes, but you end up damaging everything involved except the hammer, sometimes to the point that you can't get the lockring tool to work after the fact.
Get the lockring tool. There are semi universal ones that work ok. The type that are designed to fit specific lockrings (ie 3 slot, 4 slot) work much better. Either way they're fairly cheap.
Once the lockring is off you might be able to use your bikes chain and crank in place of a chainwhip, but this is yet another place where you're better off just buying the appropriate tool.

Once you have them you'll be a happier fixie rider.

share|improve this answer
add comment

Does it have a lockring? If not, just get a friend to hold the bike steady and try to pedal backwards.

I don't have a lockring on my commute bike and, after a series of braking manoeuvres in short succession, I've had my cog come loose while in action. That's quite scary!

If you do have a lockring then, well, you can do it with a hammer and screwdriver - it's really just a question of whether you want to reuse it again.

Or just wander into your LBS and ask to borrow their tools. Most good mechanics will gracefully decline, but will explain to you why buying one yourself is the best solution ...

share|improve this answer
add comment

With two wood blocks in a vise or drawn together by long bolts, you can grip a sprocket without damage. In the years when I placed a sprocket on my road hub (no lockring, even though a bottom bracket lockring would fit as a jam nut), it finally was on so solidly that I could skid the rear wheel without breaking free.

I seem to recall that in desperation one day, since it was a fixed gear bike, that I left the chain on the rear sprocket, while off the front sprocket allowing me to wrap the slack around the BB and secure it somehow. Then I could rotate the rear wheel forward by hand, which was able to release the sprocket.

A home-made chain whip is not too hard -- metal about 1/8" thick, drilled to allow a chain pin through. I don't think I added a length of chain for sprocket support, but rather let the 'whip' chain wrap around the sprocket. The metal piece had to be reinforced with wood to prevent buckling. Jim Papadopoulos

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.