The adjustment tag has no wiki summary.
10
votes
3answers
2k views
I often get a sore neck when riding. How can I adjust the setup of my bike to help prevent this happening?
Quite often if I'm riding for longer than about an hour I get a sore neck. I assume that I can make some adjustment to my mountain bike to help prevent or reduce the soreness, but I don't know what. ...
6
votes
2answers
1k views
Adjusting the pull/reach of STI levers with top-brakes (Tricross)
Please excuse my terminology, I have a Specialized Tricross (2008) with Shimano Tiagra STI levers, and convenience brakes on the top of the bars, running through the same cable.
Naturally, adjusting ...
5
votes
2answers
748 views
Brake callipers not long enough to allow adjustment of pads
I upgraded the standard Tektro brakes on my SE Lager to Shimano 105s. The braking performance is vastly improved. I also have Charge Plug wheels, rather than the stock wheels.
However I've noticed ...
5
votes
1answer
272 views
Nexus hub keeps getting misaligned
I have a nexus 8-speed internal hub on a Civia Kingfield bike. It keeps getting misaligned -- the dots on the bottom don't line up.
In the past I have successfully adjusted it using the barrel ...
4
votes
6answers
2k views
Adjusting disk brakes after taking off the wheel
I recently took off the front wheel off of my mountain bike, and have been having considerably difficulty getting the front wheel on the right spot such that the wheel doesn't rub against the brake ...
4
votes
4answers
835 views
How can I stop a belt brake (band brake) from squealing?
One of our bikes is an electric bike. It's an older iZip HG 1000, and although we got it through the American "manufacturer" (Currie Technologies), like most of the low-end ebikes it's made in China ...
4
votes
2answers
296 views
How deep does a quill stem need to be inserted?
I have an old road bike with a quill stem and I want to raise the stem. After raising it to where I want it, the stem has about an inch between the high end of the expander nut and the top of the ...
4
votes
3answers
494 views
Where are my barrel adjusters for my shifting cables?
I have a Devinci Caribou I and I was trying to adjust the front derailleur. I got the top and bottom stops adjusted right, but it seems that it doesn't downshift correctly from the biggest cog to the ...
3
votes
1answer
340 views
3
votes
3answers
224 views
Gear shift adjustments
I recently had to replace the shifters on my bike. The replacement was easy enough, but now when I shift the derailleur either jumps too far or too short. I've tried using the adjustment screws on the ...
3
votes
2answers
4k views
Adjusting saddle angle on a road bike (drop bars)
I'll preface this by saying that I've been a mountain biker for over a decade, including XC racing for a couple years. I've never had a hard time adjusting the saddle angle (tilt forward or back) on ...
3
votes
3answers
670 views
Fixing off-center Caliper brakes
The brakes pads of my front brake are off center, so far that when the brake is disengaged the right pad rubs slightly against the wheel even though there is plenty of clearance between the wheel and ...
2
votes
1answer
729 views
How do I prevent play in the steering post?
I recently changed my handlebar stem to an angle-adjustable variety and now there is a little bit of play in the bar coming up from the front suspension through the frame, onto which that stem is ...
1
vote
1answer
264 views
Cable adjuster recommendations
My cable adjusters always seem incredibly hard to turn, sometimes requiring the extra leverage of a wrench. I'm looking to replace them when I overhaul my bike and replace my current groupset. Does ...
0
votes
2answers
904 views
Adjust reach on Ultegra ST-6510 levers?
I'd like to adjust the reach (distance from the drop bars to the brake levers) on my Ultegra 6510 levers. The Shimano instructions don't mention the ability to adjust this at all, which seems odd to ...
0
votes
1answer
45 views
Bicycle rear hub sounding weird
My rear axle broke about 2 weeks ago, and I replaced it with a new one.
I also replaced the ball bearings with new ones when I did this.
The issue I am having is when I'm going with a higher speed ...
