The part of your bike that contains the axis the cranks arms spin 'round. (The crank arms are where the pedals attach.)

learn more… | top users | synonyms

2
votes
2answers
274 views

What do you call the crankset system type on the Sram Apex?

I see these everywhere, but no one can come up with a consistent name for them from company to company. GXP is the closest I can come to a name for the bottom bracket. ...
1
vote
2answers
774 views

Removing bottom bracket from 79 peugeot frame

I would like to remove the bottom bracket from an old french peugeot race frame. I believe the frame was built in 79 judging by the decals and stamp on the bb. The bottom bracket and spindle at the ...
2
votes
3answers
304 views

I unscrewed the lockring, and *both* BB cups rotated - what's going on?

I'm fixing up an old tandem, and the cup-and-cone bottom bracket at the front sounds very gritty, so I picked up my c-spanner and applied it to the lockring. With a bit of effort, left cup and ...
6
votes
3answers
647 views

Creaking bottom bracket

I have a Trek 3900 Mountain bike that had a serious creaking problem whenever I would pedal. I found that the ring that holds the Shimano sealed bearing was really loose. I tightened it up and it ...
7
votes
4answers
250 views

Help needed identifying mystery screws on 1940s tandem

My tandem has two small screws above each bottom bracket, one on each side (so four in total). I've not seen them on any other bike, and I can't figure out what they're for! Suggestions so far have ...
6
votes
4answers
826 views

for a single-speed conversion, is it always necesary to change bottom bracket?

I want to convert my old raleigh, which has 3 chainrings on the front, into a single-speed. Do I have to replace the bottom bracket? I keep hearing conflicting things. Thankyou.
2
votes
2answers
720 views

Attaching crank arm with Shimano SLX M660

Firstly, apologies if this question has tones of frustration, my new crank set and bottom bracket has never been installed correctly, so I am going to do it myself. Should the drive spline on the ...
2
votes
1answer
941 views

DBS 10 Speed Conversion - Bottom bracket?

I have dismantled and thrown away the old parts of this DBS 10 Speed bike I'm converting to a fixed-gear. Yesterday I received a 48T Espresso crankset, but now I wonder which bottom bracket to get. ...
4
votes
3answers
566 views

Clacking noise as right crank goes 'over the top' once per revolution

Every time the right pedal goes over the top I get a single clack noise with a little more 'travel', a point where the bottom bracket moves without any resistance, from that point in the rotation. I ...
5
votes
1answer
2k views

How can I tell the difference between a J.I.S. and ISO square taper bottom bracket?

I have a square taper bottom bracket. How can I tell whether it is a J.I.S. or ISO taper with a minimum amount of disassembly? FWIW, it's a Ritchey from 2004. However, it would be nice to get answers ...
2
votes
2answers
625 views

Bottom bracket bearing Issues

Been having some bottom bracket (BB) woes. Noticed a click on the top of the left pedal stroke decided to re-grease the BB. Took it apart cleaned everything re-greased, put it back together. Roll ...
1
vote
2answers
280 views

New rocky mountain soul 29 making creaks by the bb

Not to sure what it's coming from I don't have the tools to take the crank off or adjust the bb. The funny thing I don't get is that the creak is gone the next time I ride my bike then when I may go ...
1
vote
3answers
2k views

Bottom bracket is ticking

Recently my 2008 Devinci mountain bike sounds like it's ticking when I push down on my left pedal on a usual rotation. When I turn the bike over and go through rotations, I can't get it to tick. ...
1
vote
3answers
749 views

Noise from crankshaft spindle and then the pedal falls off

In the last 6 months I have been getting really bad noises, creaks, clunks, etc coming from somewhere around the spindle connecting to the crankshaft. Every time I put pressure down on the left hand ...
7
votes
3answers
5k views

Annoying clicking sound from the bottom bracket

I just purchased a Fuji ACR 2.0 road bike from a guy who bought it three months back but didn't ride it at all. I brought it home and found that it is making a clicking sound when I pedal. The sound ...
2
votes
2answers
474 views

Bottom Bracket Size for Specialized Roubaix Elite C2 2009

I think my bottom bracket has worn and I would like to replace it. I was looking at the Shimano 105 BB. BikePedia lists the size as 68mm, which is fine, but there seems to be another dimension. I ...
2
votes
1answer
844 views

Swap Bottom Bracket bearings or replace entire bottom bracket?

I've recently acquired a 2007 Specialized Allez. As I was dismantling the bike for service, I discovered that the bottom bracket bearings are in rough shape. They aren't smooth at all. I took apart ...
3
votes
4answers
1k views

Bottom bracket with built-in internal hub - does this exist?

I've heard that one can install a bottom bracket that has what is essentially a built-in internal hub, giving one the ability to add a virtual double chainring where there's only one. This would be ...
3
votes
2answers
500 views

Cutting down cartridge bottom bracket left cup

I have a Tange 68x103 mm bottom bracket (pictured) that I plan to use in an old steel frame (building a single-speed/fixed). It turns out that my non-drive-side bottom bracket shell threads were a bit ...
0
votes
1answer
283 views

screeching noise in bottom bracket

There is a very loud screeching noise when i pedal hard on the down stroke. Be it moving off or climbing up a hill. It is not coming from the front wheel, which i originally thought came from brake ...
2
votes
1answer
473 views

Can if fit new 105 5700 cranks on my existing 5600BB?

I am refreshing my drive train. I have been running a full 105 5600 set for a couple years. I have an ultegra cassette and chain ready to fit, and I am consdiering crankset/chainring options. Is the ...
1
vote
2answers
332 views

how to replace a bearing on BB7800?

Friends, Do anyone of you know on how to replace a bearing on BB7800 ? Do I need a special tool ? or a screw driver, and hammer would be enough to push it out ? Thanks
4
votes
3answers
603 views

Crank arms are not parallel to each other. What could have caused this?

It is a cottered crank. Crank arms themselves don't seem to be bent. It is a non-cartridge style spindle. Any ideas as to why they are not lining up?
1
vote
2answers
2k views

Will a hollowtech shimano BB fit a bike which currently has an octalink bracket?

I have a mongoose otero elite 2008 and the crankset is broke (wobbling) It's also bent, so time for a new one. I currently have a nice shimano deore crankset from an old bike, but it uses a different ...
3
votes
1answer
785 views

Will I damage anything by not replacing my clicking bottom bracket?

I have a Specialized 2010 Sirrus Sport with a sealed cartridge square taper bottom bracket that makes a clicking noise. If I don't have it replaced, will I be harming anything apart from the bottom ...
5
votes
2answers
15k views

How do I measure a bottom bracket?

I need to replace the bottom bracket bearing on my fixie. I plan to get a Shimano UN26, but I note that there are a number of different sizes. The sizes seem to be expressed as 68-110, where 68 is the ...
1
vote
2answers
639 views

Koga touring bicycle bottom bracket loose, does it need replacing?

I have a 2009 Koga Signature high-end touring bicycle (internal hub gear, hub generator, half-open chainguard, ...). I'm cycling around 100 km/week (8½ km one-way commute) plus trips, so I've probably ...
1
vote
2answers
2k views

Stationary bike “clicks” when pedaling - crank axle is moving sideways. How can I fix this?

I've got this stationary bike, a York C202, which has developed a problem - namely it "clicks" when pedaling. This is highly annoying, as there's nothing I seem to be able to do about it. I diagnosed ...
3
votes
1answer
588 views

Bottom bracket square taper (cartridge) extraction, too tight in one side

I'm getting weird noises coming from the bottom bracket (BB from now on), and I wanted to extract it to check if the problem is there or not. The guide video I used is no longer public (free) as when ...
2
votes
4answers
3k views

Cross threaded/stripped bottom bracket

I installed a new sealed bearing in my bottom bracket. Unfortunately after tightening it most of the way, it jammed and I realised I'd cross threaded it. I then removed it and reinstalled it. It ...
3
votes
2answers
795 views

What road double cranksets will work with a 108mm JIS square taper bottom bracket spindle?

So far it seems like the Shimano Sante or Suntour Sprint cranksets are the only ones that would fit my bottom bracket spindle (I am hoping to keep both BB and spindle). Am I missing any possible ...
3
votes
2answers
439 views

Chainline on a trek 660 fixie conversion

I am converting an old Trek 660 frame to fixie. It takes a 68mm bottom bracket and I'm putting in an SKF bottom bracket (like this) with both a BMX profile racing 110mm 46t and redline BMX cranks ...
1
vote
1answer
184 views

What Bottom Bracket for a 2007 Rush Hour frame?

The stock rush hour bottom bracket is a FSA BB-7420. Would a Shimano BB-UN54 that is 68 X 107mm work in that frame?
3
votes
2answers
595 views

screeching/grinding sound when coasting at speed

2003ish Cannondale six13, all Ultegra. Frequently, but not always, when I'm coasting at a fast pace, usually down a hill, the bike will start making this hideous screeching/grinding noise. It is ...
2
votes
4answers
665 views

Cruiser bottom bracket is clicking and grinding

My Trek Pure Deluxe 3-speed cruiser has been making a clicking noise when riding for some time. The problem is faint, and is more felt than heard. However, it's been getting worse; it now makes a ...
1
vote
2answers
687 views

Cartridge equivalent spindle length for Shimano BB-6207 116 mm Cup and Cone Bottom Bracket?

I'm building up an old Terry bike and will likely pick up a NOS Shimano 600EX FC-6207 crankset. The corresponding bottom bracket for this crankset is the 116 mm BB-6207 cup and cone. However, given ...
3
votes
2answers
2k views

Can a bike with an internal bottom bracket be retrofitted to have an external bottom bracket?

External bottom brackets have been appearing on higher-end bikes in the last few years. Can older bikes with bottom bracket shells that come stock with square taper internal ISO 68mm or oversized ISO ...
1
vote
2answers
1k views

Does anyone have experience with Bottom Bracket Tap/Facing sets?

I'm interested in recommending my boss get the workshop in which I work a bottom bracket tap and facing set. As it's quite an investment it's important to me to know what you're getting for your ...
3
votes
4answers
3k views

Bottom bracket making noise, should it be fixed now or can I wait until regular maintenance?

My bike has been ridden 4 months / 2000 miles and is no longer completely quiet. About a month ago I noticed a whispering noise like a wire brush sliding across a cymbal. It happens on the ...
1
vote
3answers
1k views

How long does it take to replace bottom bracket bearings?

How long does it take to replace bottom bracket bearings? Is there anything that can make the procedure take more or less time? How does the type of mechanism affect repair time?
3
votes
1answer
864 views

Are Shimano Hollowtech II bottom bracket spacers unique?

I'm moving my Shimano Hollowtech II XT crankset and bottom bracket over from a bike with 73mm bottom bracket to a 68mm bike. The only problem is that I only have 1 spacer and now I need 3 bottom ...
3
votes
1answer
2k views

How hard is it to disassemble and reassemble a bottom bracket?

I ride an SE Lager. It's a pretty cheap and crappy bike. I've had to replace pretty much everything on it due to wear/breakage. The only area I haven't tackled is the bottom bracket. I can ...
0
votes
2answers
839 views

How to upgrade a dust cap?

For all you mechanics out there I am sure you hate these things. Dust caps are the bane of my existence. They are cheap and bend easily. I want to get a better sturdier one for a bike I am working on. ...
10
votes
2answers
7k views

What are the benefits of external bottom brackets?

Pretty soon, I plan to replace the bottom bracket on my early 90's Sakae Litage road bike. It takes a standard, English-threaded bottom bracket. Right now I think it contains loose bearings--I was ...
9
votes
7answers
13k views

How to remove a crank arm with stripped threads?

A friend called me up yesterday after a mis-adventure during his attempt at a bottom bracket overhaul. He stripped out the threads on the (left) crank arm while using a Park crank puller. In a pinch, ...
5
votes
2answers
1k views

Is the plastic sleeve optional for a GXP bottom bracket install?

I took my frame to a bike shop to have the threads chased on the drive side. When I got home, I realized that they didn't install the plastic sleeve (because I didn't give it to them). They didn't ...
5
votes
2answers
5k views

Does my bottom bracket need replacing?

About two months ago I bought a Boardman HT Comp. Today I took it into my local bike shop for a service. While I was in the shop one of the technicians had a quick look at it and told me that my ...
12
votes
3answers
6k views

How do I know when to replace my bottom bracket?

With out completely removing the cranks and bottom bracket, how can I tell when it's time to replace my bottom bracket? The current symptom is a slightly 'rough' feeling when I pedal. It's not ...
7
votes
3answers
1k views

How do I stop my EBB (Eccentric Bottom Bracket) from creaking?

I have a '09 Felt Niner 29" SS with an EBB. After a thorough clean and reassembly of the BB the creaking will subside for a ride or so and then come back. Any suggestions? EDIT: the problem appears ...
13
votes
5answers
14k views

How often should I grease and repack my hubs and bottom bracket?

I am commuting 7 miles a day (round trip) in all weather in New England (temperate, moderately wet climate, cold winters). Overall I am putting about 1000 miles per year on my commuter bike, a 2009 ...