Questions tagged [drivetrain]
Questions about a bicycle's drivetrain system, including the chain, gears, chainrings, derailleurs, etcetera.
367
questions
0
votes
1
answer
63
views
Pedels move after i stop
Took everything apart cleaned regreased put back together and when I pedel to check the pedels and chain keep going what would cause it and how to fix it is a 20 inch moongoose
4
votes
1
answer
144
views
Periodic bang on bike freewheel
First of all, this is a great community :)
I have bought a trek FX 1 Stagger recently, and there is one problem which I’m not sure how to address.
There is a noise coming out of the freewheel whenever ...
3
votes
1
answer
52
views
Is play on the Schlumpf Mountain Drive chainring a problem? How to fix?
There is forward & backward play on my Schlumpf Mountain Drive chainring. Is this a problem? If so, how do I fix it?
When I hold the crank steady, there is back-and-forth play on the chainring in ...
2
votes
1
answer
123
views
pedals only move bike at highest gear
Recently my bike will only move if I’m in the highest gear. I can pedal at lower gears but it will not move my bike forward at any reasonable speed and when I get up to even a very low speed the ...
5
votes
2
answers
137
views
Trainer quieter after swapping cassette; is there a better solution?
I recently got a Wahoo Kickr Core. All working great, except the drive train is a little noisy.
I thought the easiest thing to do would be to try the cassette from my bike wheel on the trainer. The ...
4
votes
1
answer
304
views
Converting Belt Drive Bike With Paragon Sliders to Conventional Cassette
My internal gear hub broke on tour in Kenya, and now I'll need to convert my bike to use locally available parts. The frame uses Paragon Machine Works sliding dropouts who makes inserts which would ...
2
votes
1
answer
208
views
Will a Shimano Deore 11 speed chain work on a SRAM NX 11 speed drivetrain?
I went to a bike shop today and got a complete service and new chain. When I looked at the tax invoice, it said it was a Shimano Deore 11 speed chain, however I have SRAM NX 11 speed drive train. I ...
1
vote
1
answer
124
views
Crank set pairing with cassette
I have a 50-32 crankset (165mm Crank arm length) and an 11-32 cassette. I'm having difficulty when I switch up to the 50. I do Sprint Triathlons as an age grouper (70-75).
Additional information: I am ...
0
votes
1
answer
81
views
I put my bike on the bus and now the chain can't stay on
I've never had an issue with my chain falling off until today. I put my bike in the bike holder in front of the drivers window. Perhaps something got knocked or moved?
I could have a dirty cassette or ...
4
votes
1
answer
187
views
Are all top of the line components always compromising on durability in order to save weight?
It often written that top of the line components are less durable (Dura-Ace and XTR for Shimano), with the explanation that they meant for competition and so they compromise on durability to save ...
6
votes
3
answers
2k
views
Does a 3x to 1x conversion make sense for this bike?
My daughter was given a 26" hardtail with a slightly weird setup to use as a utility/commuting bike by a guy whose hobby was to build up bikes from old but unused parts... the crankset & ...
1
vote
1
answer
365
views
Running DUB wide crank with 52mm chainline
I have a set of sram xx1 carbon cranks that are DUB wide. My bike (2023 Specialized Epic Evo) is DUB crank 52mm chainline. If I add BB spacers to the DUB wide crank and use a 6mm offset chainring ...
2
votes
2
answers
1k
views
Cues U6000 and Deore M5100 11 speed compatibility
So we have two basically the same looking and working derailleurs:
Shimano u6000 and m5100. They have different pull ratios. The question is if friction shifter would allow me to mix "old" ...
2
votes
2
answers
144
views
Specialized Stumpjumper Women's HT 2006 Worth Rebuilding Back Up?
I absolutely love my Specialized Stumpjumper HT 15.5 (26" wheels), so light and nimble - a dream for single-track and general xc trail-riding (and nice and nifty for running around town too) but ...
7
votes
4
answers
964
views
Tricks for finding tick tick noise while pedaling
I’ve been trying to get rid of a ticking noise.
I think my next steps are:
a) check the chain ring for damage, and/or
b) Check the chain for damage, and/or
c) look for frame cracks
I don’t have ...
2
votes
2
answers
502
views
Are freewheels compatible if they have the same number of sprockets and teeth?
I'm a novice to the cycling world and am wanting to learn to do my own maintenance, so I'm quite unsure of a few things.
More specifically, I have a Dahon Eco C7 foldable bike that I got used and was ...
4
votes
1
answer
130
views
Gun bluing chains
Is it possible to hot blue chains for rust protection? I surmise there would be parts of a bike chain that are made using hardened steel (e.g. rollers and pins). Would this process affect their temper?...
4
votes
1
answer
346
views
New chain coming off under torque
I replaced the chain recently - the new chain unships violently when I apply a moderate amount of torque, such as when setting off standing.
As in, it comes off the big ring to the outside (i.e. away ...
2
votes
1
answer
93
views
Unable to backpedal - jockey wheels on Campagnolo derailleur
I have Campagnolo Athena rear derailleur on my road bike. Never gave me a hint of trouble. Always kept clean and lubed. Never ridden in the rain or in dirty conditions.
Yesterday I was not able to ...
2
votes
1
answer
104
views
Does this chain seem short? Does this photo indicate any obvious drivetrain issues?
Addition.
Yes this is the large-large chainring.
The shifting is rather poor but I have not tuned high, low and B, tension etc.
Thank you
I recently moved to a larger
chainring.
The shifting seems ...
6
votes
5
answers
1k
views
Training vs increasing gear ratio
I’ve just done a 1500km ultra cycling event, the lowest gear setup are front 30t back 40t. Along the journey there are many very long climbs that have more than 10% gradient. To conserve power I ...
1
vote
1
answer
59
views
How do I find replacement parts for my 1988 Suntour drive train?
I am resurrecting my old commuter which was basically a hard-tail MTB c 1988 with a 3 x 7 Suntour system. What's the least painful method (leaving shifters and derailleur intact) to replace the worn ...
3
votes
2
answers
386
views
How can I increase ebike drivetrain reliability?
I'd like to improve reliability and have fewer problems with my drivetrain. What more can be done?
I have an electric bike. I only ever use the six smallest sprockets on the 12-speed cassette, even ...
1
vote
1
answer
73
views
Will 7-speed MicroSHIFT work with 9-speed shimano cassette?
I am building out a marketplace bike. It came with a MicroSHIFT derailleur and had a 7-speed cassette on it. I want to put a 9-speed shimano cassette on and still use the MicroSHIFT derailleur. Are ...
6
votes
1
answer
508
views
Is it acceptable to have some noise on largest sprockets?
There is some chain noise on the two largest sprockets on my friend's road bike. It's not a skipping noise and not on a cross-chaining gear. Do you think it is ok to have noise on these sprockets or ...
2
votes
2
answers
512
views
Compatibility of Microshift BS-M10 10 speed friction shifter with 11 speed derailleur?
As you know it’s very hard to get any modern bar end shifters right now. Unfortunately I love them. I have an opportunity to buy Microshift BS-M10 shifters which are meant for 10 speed shimano ...
1
vote
1
answer
76
views
Can't keep new drivetrain from clicking and jumping
Recently I replaced crank, chains and cassette on my about 4 years old trekking bike. All parts are low priced Shimano parts, just as the ones I replaced. New crank and cassette have lesser numbers of ...
1
vote
0
answers
31
views
Odd chirpy noise, not chain or pulleys
So I have this familiar chirpy/twittery noise coming from drivetrain. It is under load on a down push on left crank, per revolution, lighter pedaling less noticeable. It's definitely not the usual ...
0
votes
1
answer
79
views
Lateral play in Crankset
I'm converting a ~2006 Scott Reflex to a 1x drive train, following the instructions on this video:
Convert From Square Taper to Hollowtech II Bottom Bracket/Crankset - RJ the Bike Guy
However I am ...
1
vote
3
answers
477
views
1x9 wide range cassette
I am curious to find out if anyone has figured out a viable solution for a 1x9 wide range eg; 11 to 46 or 11 to 50 setup without using a derailleur hanger extension? I have a FS mtb and am not too ...
1
vote
1
answer
690
views
What chains are OK for a Brompton?
What type of chain should I buy for my Brompton bicycle?
The chain on my Brompton bicycle is stretched, and I would like to buy a replacement. There is no Brompton dealer in my country, so I'd like to ...
8
votes
2
answers
1k
views
How to determine chain length on a Brompton?
How can I determine the correct chain length on a Brompton bicycle?
I have a Brompton bicycle with a non-standard (aftermarket upgraded) drivetrain. My chain broke and I lost some links, so I don't ...
3
votes
2
answers
1k
views
Shimano FC-RS510 compatibility with Shimano Ultegra 6800 and Shimano R7000
I have a BMC Granfondo gf01 (Rim Brake version) that was bought second-hand and came equipped with Shimano Ultegra 6800 (11-speed). Just the Crankset is different, being a Shimano Ultegra FC-6700 (10-...
4
votes
3
answers
1k
views
What do I need to consider when updating my Cannondale Topstone 4 groupset?
Last year I purchased a Cannondale Topstone 4, it was my first dropbar bike and I saw gravel as a safe do it all option as I got into cycling.
So far I love my bike but as I've become a better cyclist ...
1
vote
2
answers
91
views
Difficulties assessing whether drivetrain is worn
I've been a hobby mountain biker for a couple of years now. My bike is getting older and older (10+ years, still 26 inches) and I would like to do more maintenance jobs myself since it is not worth ...
1
vote
1
answer
277
views
I need help with total capacity of rear derailleur
I am unsure how to calculate the total capacity for a 1x drivetrain, I have 46t up front and 11-32 10 speed cassette.
How can I determine which derailleur will work with this setup? E-mtb build.
I was ...
4
votes
2
answers
129
views
Recommended torque for belt port in rear triangle?
Last week while doing a bleed and rotor replacement on my Spot Acme, my bike accidentally fell from the stand with the wheels removed, causing a little damage to the pulley:
I didn't notice this ...
1
vote
2
answers
72
views
Tandem creaking when captain pedals hard
I'm used to single rider bikes, but new to tandems. We have a specific creak that I (as captain) can also feel through the pedals. It's on every strong stroke of the captain's pedals, left or right, ...
4
votes
3
answers
861
views
Inexpensive mods for decathlon 7 speed road bike
I have a Decathlon Triban RC 100 Flat bar. It is an entry level gravel/roadie that I have had for over two years now. It comes with a Shimano Tourney 1x7 set up, which is quite underwhelming. However, ...
3
votes
2
answers
825
views
Convert the number of teeth in a chain-based drive train to the number of teeth in a gates-based drive train
If I'd convert my drivetrain from a chain-based drivetrain into a belt-based drivetrain and I'd want to keep the exact same transmission, how do I know the required number of teeth for the front belt ...
2
votes
1
answer
196
views
Shimano 7 speed shifter with 9 speed drivetrain
Can I use a Shimano Alivio 7 speed shifter with Shimano Deore 9 speed drivetrain? Basically the bike originally came with everything being set up for 7 speed. Somebody switched out my tire/rim and ...
12
votes
3
answers
3k
views
Can I update a decade-old mountain bike to modern standards?
About ten years ago, I built myself a new bike, for general utility riding and some light trips through the countryside (tens of miles on towpaths etc). I was most familiar with the classic (hardtail) ...
2
votes
3
answers
189
views
Something feels like brake rub but isn't brake rub
I brought my road bike on a flight last week and after I put it back together I immediately noticed it felt slow and muddy. It felt like I had brake rub or a mushy back tire. I'd say it feels about ...
3
votes
2
answers
183
views
Boardman Comp Hybrid 2012 - Suggestions for cheap way to get much lower gearing?
I am just about to buy a boardman comp 2012 hybrid bike which I want to use bikepacking. The gearing will be a little high as standard, it's a flat bar setup with Sram X5 9 speed shifters and rear ...
1
vote
1
answer
681
views
What is the largest cassette I can fit on a Canyon Grizl CF SL 7 1by?
I'm considering buying a Canyon Grizl CF 7 1by, but I do a lot of bikepacking in hilly areas, so I'd like to put on a larger cassette to lower the minimum gear ratio. What is the largest cassette that ...
2
votes
2
answers
2k
views
Will a 11 speed Shimano Deore crankset work with a 9 speed Shimano Altus cassette? [MTB]
I have a 2020 Vitus Nucleus 27 VR with a stripped pedal thread on the left crank arm (bought it secondhand, and am guessing the previous owner crossthreaded it). The current drivetrain is a 2x9 ...
0
votes
1
answer
682
views
Tiagra 4700 2x10 vs 105 R7000 2x11 for Gravel Bike
I'm putting together a gravel bike from parts. It will be for mechanical brakes -- cantilever at first and maybe mechanical disc later. I will be buying new shifters, derailleurs, cassette, and chain. ...
5
votes
4
answers
5k
views
Drivetrain 1x12 or 2x10 for my MTB use case?
I didn't ride bikes for quite some time and decided to start again this year. I'm currently looking for a MTB that will be kind of universal, I'm pretty much set on everything and picked few models, ...
2
votes
1
answer
572
views
Chain not meshing with new cassette
My chain is a SRAM PC-971, worn less than .75", and my derailleur is 9-speed 105. I just installed a new Shimano HG-400 cassette, and it seems like the chain isn't 'meshing' correctly, causing a ...
3
votes
1
answer
452
views
Looking for an optical gear display solution for a Shimano Ultegra 10 speed 6700 group set [duplicate]
I upgraded my wife’s road bike for a 2011 carbon Devinci CX4 equipped with an Ultegra 6700 groupset.
She’s missing the optical gear indicators she used to have on the shifters.
I already looked at the ...