Usually means the front fork, where the front wheel sits. Can also mean the rear fork, a part of the frame.

learn more… | top users | synonyms

0
votes
1answer
29 views

Front wheel Fork is having scratches and Oil is getting leaked from it?

I thought that it might be a fault of Oil seal but Mechanic was telling that I have to replace both the fork If I replace only the Oil & Oil seal then again It will leak oil. Is it a dangerous ...
1
vote
1answer
44 views

Having the fork blades aligned

I got a classic steel road bike, gazelle tour de France, and one of the fork blades was bent in the frame direction, some two centimetres, after a crash. I read here that this can be realigned, I'd ...
0
votes
1answer
29 views

Torque for front caliper bolt. [duplicate]

What's the recommended torque of the front caliper bolt for a carbon fork? The Fork is from a Felt F1. I don't want to damage the fork from over thightening.
0
votes
2answers
1k views

Tapered fork into 44mm head tube?

I have a MTB Ghost SE 2000 frame which has a 1 1/8" head tube. I just measured it and it has a 44mm diameter top and bottom. I want to replace the stock fork. However it is hard to find non-tapered ...
1
vote
1answer
49 views

Retrofit lockout for a suspension fork?

I am new for cycling. I am searching for bikes on which I will ride mostly on roads, but also on terrains/mountains occasionally. After doing a few researches online, I finally decided to buy a hybrid ...
0
votes
2answers
385 views

Upgrade suspension on hard tail MTB

I have a Suntours xcm (spring 80mm) on my hard tail. I drive more frequent and more pretentious. So I consider to upgrade my fork. How can I tell if I need a better one? What can a good air-suspension ...
1
vote
2answers
587 views

Cantilever brakes for older narrow fork bosses (55mm)?

I have an 80s cyclocross frame I am restoring. The fork's cantilever bosses are spaced at 55mm - much narrower than the modern standard (around 70mm I believe). I tried to fit a pair of Tektro ...
0
votes
0answers
25 views

Replacing Suntour M3010 with rigid fork (sag and measurements)

I have an entry level Giant Revel 3 (2014). The Suntour fork is horrible. But, I like the frame and, to me, it's worth doing a couple of minor things. I use the bike for communiting and, from what I ...
0
votes
1answer
73 views

Building an Entry Level MTB. How should I choose suspension forks?

I am new to Mountain Biking. I just bought a CRONUS HOLTS 330 (Hardtail) with Shimano gear system and disk brakes. Its a 19" frame with 26" tyres. All aluminium pretty light weight. The brakes are ok ...
0
votes
2answers
49 views

What fork will fit my bike? [duplicate]

I have this bike: http://www.bikebarn.co.nz/2015-merida-big-nine-20d-white.html I want to swap out the forks for some rigid forks. Please tell me what specs I should be looking at to get the right ...
0
votes
0answers
113 views

Fox Float CTD Evolution vs Fox Float CTD Performance

What is the difference between Fox Float CTD Evolution and Fox Float CTD Performance? Except that one is most expensive and better? I mean real difference...
2
votes
2answers
87 views

Safe steerer spacers stack height

I'm building my first road bike, which means I'll have to find appropriate bar height through personal experience and cut the fork steerer in process at least once. I plan to start with the following ...
1
vote
1answer
151 views

Is there more than one type of tapered steerer?

I have a set of forks (Rock Shox XC/30/TK on a Focus Black Raider 2.0 2012) that measure 30mm at the bottom and 28.6mm at the top, (or 1 3⁄16" to 1⅛" in pre-enlightenment measurements). So they're ...
-1
votes
3answers
143 views

No non-sus 29er mtbs? [closed]

So I sat down and said "what kind of a bike do I want?". I ride mostly in the city, but I wanted something that I could take out to the trails. I don't do anything crazy... maybe a 2' drop at the ...
1
vote
0answers
153 views

Rigid fork replacement for Rock Shox Bluto fat bike suspension fork? [closed]

I'm considering the purchase of a fat bike with a Rock Shox Bluto Fork. This fork takes a 150x50mm Maxle Light and 150mm hub. However, since winter is coming and I'll likely be riding in slop and ...
0
votes
0answers
38 views

How to clean and lube SR 29 XCM-HLO fork?

I want to clean and lube my fork , and found this video on youtube ...
2
votes
1answer
70 views

Carbon fork torque

I notice that my fork is squeezed together when I tighten the quick release mechanism. Is it possible then to over torque the quick release and squeeze the fork too close together?
8
votes
1answer
1k views

Hard fork and low tire pressure or viceversa?

With mountain bikes, what do you think is more efficient: highly preloading the fork and using low tire pressure or having a "bouncy" fork and hard tire pressure? I like to have the fork with quite a ...
2
votes
3answers
194 views

Rockshox Quadra 21R — Removal tips for old brittle elastomer

I am tuning up the mountain bike I purchased in 1994, which has the old yellow Rockshox Quadra 21R front suspension fork. I have found a nice video on YouTube which shows how to service the ...
1
vote
2answers
85 views

Wheel Wobbles and Rubs on Brand New Bike?

I just got a brand new bike and it came partially assembled in the box. I don't have a whole lot of experience when it comes to working on or building bikes but I managed to put it together. theres a ...
2
votes
1answer
234 views

Are single-sided forks a gimmick? [closed]

The first time I saw a Cannondale with a one-sided fork I was in shock & awe. But I got to thinking about it, and it seems to me like it's just a marketing strategy, touting the quality and ...
2
votes
3answers
135 views

Inflating airspring fork with Topeak products

Today in receipt of a Topeak "Pressure-Rite Schrader Valve Adapter" to inflate my airspring fork, thinking it would work perfectly with my Topeak "JoeBlow Pro" floor pump. It doesn't work very well, ...
3
votes
4answers
4k views

Badly rusted suspension fork

I have a $300 MTB used for commuting. It has been three years now, and the rain and snow have said their word. Two weeks ago I disassembled the fork and spent a good one hour with the sandpaper, ...
-1
votes
1answer
81 views

I need help planning my bike renovation!

I'm planning on buying this bike online and making it, well y'know, mine. And to do this, I would like to make it look like an Aristotle bike. So I'm basically am going to need new rims to start and a ...
0
votes
3answers
93 views

Are front forks supposed to pull to centre?

So I took my bike in to the repair shop, to have the rear wheel replaced, but after the repair I noticed immediately the steering feeling a bit strange. I've since worked out why. The problem is that ...
0
votes
1answer
125 views

SR Suntour XCM v3 forks Headset

Currently building a new mountain bike and for the time being I'm using the old forks until I buy some new ones. My question is how do I find out what type of headset I need? Because from my ...
6
votes
1answer
264 views

Why would higher fork contribute significantly to breaking the frame?

When I recently cracked my frame near the headtube, every bike shop that I went to, asked me explicitly "Did you put a longer travel fork?". Putting aside that apparently fork travel and fork crown ...
5
votes
4answers
1k views

What is the advantage of a reverse arch suspension fork?

There are a couple of suspension fork manufacturers that have adopted a fork design where the lowers have a reversed arch. I can't see that they claim any particular performance advantages for it, ...
3
votes
2answers
93 views

torque specification on headset

I was wondering why there is a torque specification on the steer tube end of the stem for mountainbikes. The torque specification that goes to the handlebar is reasonable, after all handlebars are ...
17
votes
5answers
2k views

Is front-suspension a false-economy for cheaper bikes?

I'm a 30 year old male looking to purchase my first non-department store bike. I haven't biked in more than a couple years. My use-case is 90% asphalt (inner-city, occasional low-speed highway) and ...
1
vote
0answers
101 views

Lowrider style bent forks techniques

Would a 24 inch bent fork fit on a 20 inch frame? Is there even a 24 inch fork? Would a 26 inch fit? Also if it doesn't fit in could I just add to the 20 inch - would you be able to extend it making ...
3
votes
2answers
622 views

Dual position air, solo air, coil, rebound: what do they mean about forks?

Lyric is available as Dual Position Air/ Solo Air / Coil. What do those terms mean generally? My speculations are leading me nowhere. If Dual Air means no hydraulic cylinder, how can the fork have ...
0
votes
1answer
399 views

Replace 140mm fork with 160mm on Remedy 7 27.5 possible?

I'm Curious about whether it's possible or whether Remedy's frame is designed for such a replacement. Some bicycles makes it possible to upgrade to longer forks. I searched in Google, some people say ...
2
votes
2answers
122 views

I need to change my fork after having an accident with my bike

I need help as I need to change the fork for my bike (Ridgeback Speed 2013 Womens Hybrid Bike) I live in London and I went to few shops but in all of them they need to order the fork and it will cost ...
0
votes
1answer
99 views

Help with pairing the right headset to a new 3T fork

I recently purchased an Aventon Mataro (http://aventonbikes.com/track/) frame and a 3T Funda Pro with tapered fork (1 1/4' - 1 1/8' 1.25 ). I've been trying to figure out which headset I need to fit ...
4
votes
3answers
3k views

Why isn't my suspension bouncy?

I recently bought a Carreras centos limited edition mountain bike. I want to find out how to make my suspension bouncier and I want to experience a MUCH more comfortable ride. I have tried fiddling ...
0
votes
1answer
249 views

Dual air forks negative positive chamber pressure equality

Regarding solo air forks everything is clear. Once we bumped both chambers pressure is equal. But why for dual air forks air pressure doesn't try to get equal in both chambers? What's the point of ...
1
vote
1answer
111 views

What is the problem with my suspension fork?

I have a Manitou Skareb. I think it is a 2005. It was working fine the last time I rode it. I pulled the bike out after about 1 month of not riding and I could push the fork down about 1.5 inches with ...
2
votes
3answers
158 views

Bike type xc ht or cx? [closed]

I am a newbie on bikes and i want to buy one. I want to buy a bike that i can cover some small city road distances ~30km daily with comfort and to be able to go on some mountain trails when i got time ...
0
votes
2answers
107 views

Carbon Fork Noise

I've got a 2 month old Cannondale Evo Supersix. When I take it over a rough patch of road (far too many of these in Wiltshire!) there is a loud noise coming from the forks - it's obviously caused by ...
2
votes
1answer
250 views

Road Bike Bending Rear Skewers

I'm pretty handy with bicycles, but I'm a little stumped on this one. Have a 90s Cannondale SR800 which is solid other than the back wheel was angled to the left side of the chainstays. Ridable, but ...
2
votes
1answer
2k views

Suspension fork swap for rigid: axle-to-crown confusion

I'm looking to replace the suspension fork on my bike with a rigid one. After much soul searching I've tentatively settled on the Surly 1x1. What's got me wrapped around the axle (pun intended!) is ...
1
vote
3answers
383 views

Should cheap suspension forks be oiled often?

Should a cheap fork be oiled / lubricated from time to time? If yes, how?
2
votes
1answer
82 views

Are both sides of a Avid rotor the same?

i've got a Cotic Roadrat, and the disc mount on the fork is on the right hand side (as you're seated). However, the front rotor of the avid BB5s (road) i just bought can only be fit on the left fork ...
1
vote
2answers
1k views

Fox Talas RLC fork not rebounding, and compressing under no load

I have an older fox Talas RLC fork. It rebounds under no weight fine, but even just sitting and pedaling it compresses fully. If i pull up it will rebound, or get off it will rebound. But it seems ...
1
vote
2answers
1k views

Where can I get a new steer tube or 1 1/8" 6061 Aluminum Rod Stock?

I have an Anti-Gravity fork that features a removable steer tube, but it is a threaded fork. Where can I buy a threadless steer tube to clamp into it to convert it? All I can find are threaded steer ...
11
votes
3answers
11k views

Replacing suspension with a solid fork

I have an older version of this bike: They have made some changes to the components since I bought my bike but it is more or less the same. Here are the specs on the newer bike. I was hoping to ...
1
vote
2answers
345 views

Can a 120mm fork be mounted on Specialized Myka?

I have this fork available: RST Gila T8 (120mm travel option). The 80mm XCT fork on a 2-year old Specialized Myka is getting worn. I am considering installing the fork. Here it is explained that ...
3
votes
2answers
2k views

How do I identify an SR SunTour fork exact model?

I recently located this SR SunTour service manual, containing schematics of a load of forks. Trouble is, my fork only has "XCR" on a sticker, and production date stamped. At some forum this is ...
0
votes
1answer
343 views

Maintenance of Fork springs on Marzocchi Bomber Dirt Jumper

I recently took my fork into my mechanic for service because it was making a rattling noise in one of the fork legs. Upon initial assessment he thought it was a broken return spring for the air ...