Usually means the front fork, where the front wheel sits. Can also mean the rear fork, a part of the frame.

learn more… | top users | synonyms

3
votes
3answers
805 views

When is using a suspension fork worth it?

I've recently picked up biking again since my childhood years, so I'm quite the newbie. I've figured out most of the features I'd need so far but I'm at a loss at this one. Why would you pick front ...
2
votes
1answer
168 views

How can I fit this mudguard?

I thought this would be simple. The problem is that the entire brake assembly needs to be rotated to screw into a thread built-in to the fork. There's also a hex/allen hollow tube-nut at the back ...
5
votes
1answer
1k views

Suspension fork - Can you leave them locked for a long time?

My bike's two years old (about 1800km on it, almost all road and bridleway) and kept in a garage. Back in November or so I locked the front suspension fork for road-riding, and over the winter ...
1
vote
2answers
319 views

What torque for caliper brakes onto carbon-alloy forks?

I've recently got a new bike with a Kinesis DC07 carbon/alloy fork. This comes with deep-drop calliper brakes (Shimano R451 Dual Pivot). The first time out I bumped one of the brakes and it twisted ...
3
votes
2answers
875 views

What is the advantage of a reverse arch suspension fork?

There are a couple of suspension fork manufacturers that have adopted a fork design where the lowers have a reversed arch. I can't see that they claim any particular performance advantages for it, ...
4
votes
3answers
1k views

Why isn't my suspension bouncy?

I recently bought a Carreras centos limited edition mountain bike. I want to find out how to make my suspension bouncier and I want to experience a MUCH more comfortable ride. I have tried fiddling ...
0
votes
1answer
91 views

Missing a part from an internally threaded steer tube

I recently obtained and then disassemble a Kink Co. BMX. It had a threadless headset. Unexpectedly, instead of having a star nut inside the fork's steer tube, the steer tube was internally threaded ...
1
vote
3answers
526 views

If I replaced the fork on my cyclocross bike with a track fork, what would be the effect on the bike geometry?

If I replaced the fork on my cyclocross bike, surly cross check, with a track fork, what would be the effect on the bike geometry? What would be the effect of the modified geometry on bike handling. ...
5
votes
1answer
598 views

conversion to rigid fork

Is it possible to put a rigid fork onto a 120mm travel hardtail without upsetting the handling? I used to ride a Kona P2 fork on a 96 AA frame, which I suppose was designed for a max. of 100 mm ...
3
votes
2answers
241 views

Trying to build a bike, confused about fork/headsets/compatability

I have a fork with a 1" steerer tube, and a frame with a 1.5" head tube. The steerer tube is slightly short, and when inserted into the frame, is flush with the top of the head tube. The fork is ...
3
votes
1answer
883 views

Is it possible to replace a 1 1/8 steering tube with a 1"?

I have a 94 Giant ATX. Threaded 1 inch steeering tube. I need a shorter stem, and would also like to install a suspension fork. Is it doable? Could I take a modern suspension fork, heat the crown, ...
1
vote
3answers
770 views

Is it safe to ride with bent fork?

My bicycle went from this when I bought it: To this when I crashed (note the front fork bent where it attaches to the stem; front wheel almost touches the down tube): Update: Just looked at the ...
-1
votes
1answer
381 views

Fork MTB clearance problem

I have a felt Nine comp. It is a 29er with rockshox forks. The clearance is poor with a continental rubber queen tyre. Is there anything I can do to increase the clearance? (we're talking 1cm, which ...
2
votes
2answers
691 views

Any wheel on any fork / frame?

I have been braking for a bit too long with worn off brake pads on not so new rims so I basically killed them. I currently have the stock wheels of an FX Trek 7.2 bike. I will most probably change ...
2
votes
1answer
191 views

2009 Boxxer Team Dual Crown - Are springs different from 2010 + models?

I have a 2009 boxxer team fork on my bike. I'd like to buy the firmer spring as I am heavier than the last owner. Can I put the spring from a 2010/2011/2012 boxxer in there or was there something ...
3
votes
4answers
3k views

Badly rusted suspension fork

I have a $300 MTB used for commuting. It has been three years now, and the rain and snow have said their word. Two weeks ago I disassembled the fork and spent a good one hour with the sandpaper, ...
2
votes
1answer
370 views

Suspension Fork Axles

I'm looking to upgrade my suspension forks from Rock Shox Dart 3 to something like Rock Shox Sektor RL. A lot of the forks have either a 15 or 20 mm axle, or 'Maxle'. What does this mean? Will this ...
0
votes
1answer
284 views

Front suspension fork woes

I recently bought a preowned Saracen Havoc 2000 (Team Saracen edition) and had to replace the original forks (Zokes branded double crown) as they were seized solid. Replaced them with an old but ...
7
votes
2answers
10k views

What maintenance does a front suspension fork need?

I've just bought a used bike on eBay, its a 2002 Marin Bobcat Trail. It has 'In-Sync 266' suspension forks. This is my first suspension bike so I need some guidance in the use and maintenance of these ...
1
vote
2answers
385 views

Does “Carbon & Aluminium” really mean cheap plastic coated aluminium?

I'm looking to replace the suspension fork on my MTB (which has blown a seal) with a rigid fork now that I'm exclusively commuting in the city. During my research I came across the MOSSO 26" MTB ...
0
votes
2answers
267 views

RS Revelation '11 dual air fork leaks

I have a RS Revelation dual air fork. It's new, never used before. I installed it and after a few days I noticed, that it loses air. Maybe 20-30 psi over night. So at morning it's just too soft and ...
0
votes
1answer
327 views

Gap between fork and frame

I removed the fork from my old racer because I was hit by a car. When I'm trying to put the new fork on the frame, I get a gap where the top bearing is situated. What should I do? Could I just remove ...
2
votes
4answers
908 views

How can I remove a fork if the bolt on the stem is rusted?

I got run over a car a few weeks ago and now i have to change the fork. It's an old racer, as you can see in the picture, with a 1 inch fork. I am trying to loosen it from the frame, but I can't ...
0
votes
2answers
3k views

Where can I find a fork pressure guide?

I have a SR Suntour Rux S 130 mm fork and I don't know what pressure should I put into the left valve. For some reason I think this fork should have only 0 - 15 PSI pressure, but I don't know what ...
1
vote
3answers
4k views

What options do I have when replacing my fork's elastomers?

I'm rebuilding an AntiGravity Fork and converting it to threadless for my 'Blast From the Past' bike (GT Bravado frame, U-Brake, Bullseye hubs and cranks, 21 speed). I really like these forks and I'd ...
1
vote
2answers
1k views

Where can I get a new steer tube or 1 1/8" 6061 Aluminum Rod Stock?

I have an Anti-Gravity fork that features a removable steer tube, but it is a threaded fork. Where can I buy a threadless steer tube to clamp into it to convert it? All I can find are threaded steer ...
1
vote
2answers
1k views

100 mm front hub, 94 mm fork dropouts, options?

Simple as that. I thought I could He-Man the fork to fit the hub as it's only 3 mm on either side. Looks like it requires a bit of force and I'm concerned about breaking something in the long-run; ...
0
votes
2answers
2k views

Good resources to learn about forks

Quick question. I have a lower quality mountain bike with a bad suspension fork. Overall the bike isn't bad. It fits me well and I have a lot of fun on it. I would like splurge on a new mountain bike ...
1
vote
2answers
1k views

Fox Talas RLC fork not rebounding, and compressing under no load

I have an older fox Talas RLC fork. It rebounds under no weight fine, but even just sitting and pedaling it compresses fully. If i pull up it will rebound, or get off it will rebound. But it seems ...
1
vote
2answers
748 views

Why does a bike frame have to be above 56 cm usually to fit 700c tires?

I first came across this when I was looking at the Surly LHT, but I started to see it everywhere. It seems to me they can just put on a longer fork or something, or is it more for the back wheel?
12
votes
4answers
29k views

What is the “preload” setting on the front fork suspension?

I've made a photo of the actual "thing" as I find it very difficult to explain otherwise: I'm wondering what this "thing" sets and how it actually works. So, what is "preload" and what happens when ...
3
votes
3answers
1k views

Can I use normal grease for a car on the surface of carbon bike?

Helo Guys, I want to know your experience about carbon material and grease Can I use normal grease with carbon ? I want to put grease onto fork and stem.... Or WD-40 or silicone penetrant would be ...
7
votes
2answers
6k views

Is it possible/sensible to add a suspension fork to an old mountain bike?

I have a ~1993 Giant mountain bike. It's not great, but I am a very new and casual rider. The bike has a solid fork and it makes for the predictable rough trail ride. The trails are generally ...
1
vote
3answers
308 views

What's the beefiest front shock (26"), avail in quick release, with travel of 100-125mm (no more)?

Details: I mostly enjoy XC and all mountain riding. However, I also from time to time, will go out with friends on some much more intense downhill trails. I'm also about 240 pounds, give or take. ...
0
votes
1answer
257 views

Raleigh Twenty forks too narrow to accept 93mm hub

93mm hubs are standard size for the R20s but on this particular bike there isn't enough clearance between the fork ends to get a wheel in (I'm using an original R20 wheel as a replacement so it's ...
4
votes
2answers
888 views

Road Fork: Curved vs Straight?

I found a frame I'm interested in building up, but it doesn't include a fork. So I've been looking for carbon 700cc forks... with disc tabs. I've found a few, but ran into a new dilemma - curved vs ...
5
votes
2answers
3k views

How do I measure a fork for suitability?

I have an old bike I bought from ebay that looks to be '80s vintage. I'm converting it to a single speed. I have some new(ish) wheels that I plan to use. I tried to just slot in the existing wheels ...
3
votes
3answers
4k views

Are modern forks compatible with older style bikes?

I have an old 10-speed bike (likely 80's vintage) with a threaded fork. Can I replace it with a modern threadless fork with the style of stem that slides over the top of the fork and clamps on? I know ...
1
vote
2answers
1k views

Installing a compression plug

I am currently building a bike up. I have a carbon fork, with a carbon steer tube, and I have to install it using a compression plug. I picked up one of these this morning: ...
1
vote
2answers
2k views

Is there a sign that a fork needs hydraulic/lubricating oil changed?

What are the signs that a fork needs an oil change? I'm asking this because lately my RS Revelation (1yo) seems stiff. I checked the sag and found I should increase it... so I did, but it's still ...
4
votes
2answers
826 views

Can a steel fork be unbent?

I was hit by a car and now the steerer of my Reynolds 753 aero fork is bent. Is it possible to bend them back? Would that be safe? I can't afford a new pair!
1
vote
1answer
688 views

Avalanche upgrade cartridge for Boxxer, or tune existing?

I've got a stock Boxxer RC 2011 on my bike, and I'm not overly impressed with it's damping. On fast small bumps it tends pack down, and on big hits it bottoms out. As it's only got overall external ...
7
votes
3answers
9k views

How do I choose a bicycle fork?

I'm putting together a bicycle on a budget from a frame I was given and various parts from a bike with a broken frame. The only part of any expense that I really need is the fork, and I want to get ...
1
vote
2answers
4k views

Will changing suspension fork travel change geometry of bike?

Assuming that the sag of the new 120mm fork will be set to the same as the old 100mm fork and headset spacers will remain constant, will the geometry of my bike change moving from a 100mm travel fork ...
3
votes
2answers
424 views

What are early signs of failure in forks/stem/handlebars?

I ride an SE Lager. In the past year, the following components have worn out or broken Front chainring Rear cog Rear freewheel Chain Seat (one of the bars snapped off) Many, many spokes Wheels ...
3
votes
1answer
308 views

Proper fork length for a bike with 5.5 inches of rear shock

I purchased an older Santa Cruz Blur frame today. From what I can gather the shock mounted on the frame gives 5.5" of travel. I'm looking to buy a fork to match. Do I need to go with a 140mm fork, ...
5
votes
2answers
3k views

Fork lube. Should I use it? If so how often?

I ride a mountain bike with front suspension. I've recently seen fork lube for sale on an online retailer. This got me thinking. Do I need to be using fork lube? How does it help? If I bought some how ...
10
votes
4answers
2k views

Is it safe to remove “lawyer tabs” on a carbon fork?

Is it safe to file off the "lawyer lips" - the little tabs on the end of the fork dropouts - on my carbon road fork? What about cyclocross forks? I've heard it's "common sense" to remove them...
2
votes
1answer
211 views

Why would semi-solid fork make whizzing sound?

Alert the semi-solid fork is probably not the right terminology, it shows that I don't know 100% whether the work has some sort of inner suspension. My bike is almost this one but I feel there is ...
9
votes
3answers
10k views

Replacing suspension with a solid fork

I have an older version of this bike: They have made some changes to the components since I bought my bike but it is more or less the same. Here are the specs on the newer bike. I was hoping to ...