Handlebars are the part of the bike where the rider holds onto for grip and steering of the bike.

learn more… | top users | synonyms

4
votes
3answers
378 views

Would Lowering my Handlebars Help my Performance?

I ride now with pretty decent comfort, I have no real back/neck/shoulder pain. As I ride now I feel decent, but I feel as though I might be in too much of an upright position on the bike to get the ...
6
votes
4answers
518 views

Adjust handlebar position/height (damaged screw?)

I was trying to adjust the position of my handle bar...but might have turned the screw too hard in the wrong direction or perhaps it was like this earlier...not sure.... Is there anything that can be ...
5
votes
4answers
3k views

How to cut carbon handlebars

Last year, I installed carbon bars on one of my mountain bikes and I'm finding them too wide. I've been told that taping over the points you're going to cut at will prevent fraying/roughness, but what ...
3
votes
2answers
289 views

Interrupter (cross) brake lever cable guide wedges?

Interrupter brakes require the brake cable to angle away from the bar to meet the lever at the proper point as shown in the picture below. You can see the handlebar tape doesn't carry on closer to the ...
3
votes
5answers
5k views

How do you make the handlebar stem straight?

I adjusted my stem height the other day, and since then, the stem hasn't felt straight. I've attempted to straighten it a few times, but because I'm just eyeballing it, the handlebars don't quite seem ...
3
votes
2answers
176 views

Replacing the handlebar grips with ergonomic ones?

I had bought this set a while back and I eventually managed to replace them the other day, but... It didn't work! The length of the bar is too short to reach the end of the new grips, i don't know ...
0
votes
1answer
47 views

Stem diameter question

Changing to an adjustable Ritchey stem on my Trek 7.3. My bars are 25.4 and the stem I'm looking at is stated to be for 25.8-26. With this being half a millimetre bigger, will it still fit ok? Many ...
2
votes
2answers
607 views

Can I put standard drop brakes on a MASI drop handlebar?

I've got a set of handlebars from a MASI Uno. I'd like to know if I can put standard drop bar brakes, similar to these (ignore the interrupter brakes and bar end shifter for now). The MASI bars ...
0
votes
0answers
43 views

Converting my Giant Roam 3 into more of a road bike, while keeping its hybrid identity? [duplicate]

I am not rich so the budget is as low as possible. I use my bike for pleasure mostly as I am still a teenager. Of course I want speed, so I was wondering how well it would work if I changed the tires ...
25
votes
8answers
46k views

Pros/Cons of Bar-Ends?

I've always heard "never use barends" and they're banned equipment for some of the local clubs/group rides. A number of people on-line swear by them though. What's up with that!? :-) Why would I ...
2
votes
1answer
2k views

Loose Handlebars

I recently got into a small bike accident and the handlebars became loose. It seems to not be in sync with the front bike tire. I tried to tighten the headset and locknut, nothing seems to work. I can ...
1
vote
4answers
172 views

Commuting on flat terrain/handle bar

For my new job I'll have to commute about 10 - 20km (6 - 12mi) each day (one trip) in flat terrain. Right now, I'm commuting 6km/4mi each day, with an elevation gain of 160m uphill to work. I'm ...
4
votes
4answers
4k views

Bent Handlebars

My girlfriend recently got a new road bike. After getting it home we realized that that handlebars were quite badly bent. Here is a picture. Here is my question. Can I try and bend the bars back ...
7
votes
1answer
394 views

Knee position while on the aero bar

I find that my knees are coming ahead of the pedals while I am on the aero bars. I am not sure whether this is right or wrong. In the below image, I don't feel pain on my lower back for a long ...
4
votes
2answers
312 views

How is Sir Bradley Wiggins 3D printing his titanium handlebars?

I just read an article about how Sir Bradley Wiggins is going to try to break the 1 hour distance record soon. In it they mention One of the unique new features is a set of 3D printed titanium ...
6
votes
1answer
417 views

How does a quill stem without a front bolt work?

Looking at quill stems I noticed this rather curious one and I couldn't imagine how it secured the handlebars without an apparent bolt. Any ideas? more images
2
votes
2answers
81 views

French handlebar fit

I have an Atax stem ('85 Peugeot). Original steel handlebars are 25 mm. Is it prudent to spread the stem to accommodate Nitto 25.4 randonneur bars?
2
votes
3answers
1k views

Replacing mountain bike bars & stem with drop bars

I have a mid-1990s Specialized Rockhopper. I've trashed the flat bars that were on it previously and I want to install drop bars, but to make that comfortable for me I'll want a shorter and higher ...
2
votes
5answers
4k views

How difficult is the switch from flat to drop bar?

I've ridden with flat bars for more than 10 years, both freeride and commuting. Now I'm considering switching to a road bike with a drop bar for commuting. I went to a shop and tried a couple of such ...
0
votes
1answer
62 views

Does anyone know who made the part that attaches the shifter to the bar?

http://imgur.com/cvWOSbS Looking to set something up like that with bullhorns, cant find the part to attach shifter to bar.
1
vote
1answer
127 views

Reason for handlebar diameter

Why are handlebars the diameter they are (22.2 or 23.8 in grip area)? In general, the best diameter for grip strength is where the hand around the grip has about 1mm from the tip of the middle finger ...
2
votes
4answers
927 views

Does anyone sell a direct-drive recumbent with no handlebars?

This document well describes the benefits of a direct-drive recumbent. Is there any carbon-frame recumbent, commercially available, that implements all its recommendations. And what are the pros and ...
1
vote
3answers
453 views

fixie brake lever

I've got a bit of a dilemma with regards to brakes on my fixed wheel bike. Currently I've got both brakes on, as standard road levers on the hoods of the drops, but now I'm running fixed instead of ...
8
votes
2answers
390 views

What is the purpose of this small block on the handlebar?

What is the purpose of this small block on a handlebar? This article on "bicycle archeology" (in Dutch) describes that they have almost completely disappeared, and are found only on very old ...
2
votes
1answer
447 views

Can I use 25.4mm bullhorn brakes on a 26mm handlebar?

I've got a 26mm bullhorn handlebar but it seems like many stores sell bullhorn brakes that are for 25.4mm bullhorns. Will this 0.6mm make much of a difference? Would it be okay to use the 25.4mm ...
2
votes
1answer
174 views

How do I remove old hockey tape from drop bars

I used hockey tape on the drop bars for my bike and I need to remove it to replace the brake levers. Over time, the tape has become melted/fused together, and I used lots of layers for extra ...
2
votes
1answer
352 views

Can´t remove BMX stem top cap bolt (won´t loosen)

I was trying to remove the handlebar and stem of my bike in order to be replace them. The bike has got a BMX stem and the top cap bolt is spinning freely in both clock and counterclockwise. Any idea ...
4
votes
2answers
2k views

Choosing a handlebar width

Are there any rules/tips to choosing a handlebar for your bike? I live in a big city, and I've seen fixies with really, really narrow handlebars (presumably to avoid hitting pedestrians?) I ...
14
votes
5answers
3k views

Deterrents against partial (component) theft

Big question: Is there any way to increase the security of bolted on portions of a bicycle? Specifics: I cycle as my primary mode of transport (in East London) on a early 90s steel road bike with ...
3
votes
1answer
393 views

Can lock on grips go with carbon fiber handle bars?

How prudent is it to install lock on grips onto carbon fiber mountain biking handle bars? Are there some grips that will work and some that won't?
-1
votes
1answer
139 views

I need help planning my bike renovation!

I'm planning on buying this bike online and making it, well y'know, mine. And to do this, I would like to make it look like an Aristotle bike. So I'm basically am going to need new rims to start and a ...
3
votes
1answer
2k views

handlebar under-tape (extra layer)?

I'm going to be re-taping my bars for the first time soon, and I was thinking about a putting an extra layer of tape for just slightly increased diameter and padding. I have big hands, but I don't ...
0
votes
4answers
558 views

Bike too big for me

I bought a bike online based on a recommendation that a 56cm frame would be ok for me (I am 5ft 10, with 30" inside leg). However I think it is slightly too big. I have to lean forward a lot and my ...
4
votes
2answers
2k views

Handlebar stem : height vs length

I want to decrease the reach of my handlebars. Does it matter whether I increase the height or get a stem with a smaller length(extension?) on my bike? And is there any way to calculate the relation ...
-2
votes
1answer
132 views

What can cause direction to wobble?

When I cycle I can feel wobbling in the direction. I feel it even more and can even see it if I ride no handed. It gets really bad when I put luggage on my low rider. The bike is a 62cm touring steel ...
6
votes
4answers
5k views

Can I put bullhorn bars on a bike with hydraulic disc brakes

The most comfortable bike I've ever owned was a road bike with bullhorn (aka pursuit) bars. I actually had a pair of STI levers on it, mounted upside down (with the handles pointing forward). They ...
1
vote
1answer
86 views

Will loose handlebars result in slower riding?

I went for a ride this morning and my handlebars were loose. I now realize that it is unsafe to ride like that but my average speed was dramatically lower. Do you think it is because of my loose ...
7
votes
2answers
414 views

Need a method to wrap H-bars with handlebar tape

I've gotten good at wrapping drop bars, using conventional cork tape: You start at the end and work your way up, keeping the tension even and watching the overlap, and it works perfectly for me. But ...
3
votes
2answers
2k views

Why do my handlebars wobble left and right?

I got this bike secondhand, and so I don't know its history/what could have made it like that. And I mean they wobble while I'm holding them, not while I'm riding hands-free only. I've ridden a few ...
10
votes
2answers
7k views

My brake lever is coming loose from my handle bars; how can I tighten it?

I have a road bike with drop bars, and the left brake lever is slightly loose - it can rotate a few degrees around the handle bar from side to side. How can I tighten it? Is it possible to do so ...
3
votes
1answer
185 views

Installing handlebar

I've bought a 25.4 mm bullhorn for my fuji feather 2013, and I tried to install it.Then I've realized that my quill stem is for 26 mm handlebar. Are there any ways to install 25.4 mm handlebar into 26 ...
9
votes
3answers
5k views

V-Brake levers for drop handlebars?

I would like to try the drop handlebar on my touring bicycle that has V-Brakes, and Shimano 9x3 speeds. Are there drop handlebar levers (integrated shifters would be great), that have correct pull ...
2
votes
1answer
179 views

Replacing a shifter

One of my plastic shifters broke and I am looking for a replacement on the internet. How do I know whether a replacement will fit my handlebar. Are all handlebars the same size?
3
votes
4answers
5k views

BMX stem slipping; how to stop?

I recently bought a BMX bike that currently has all stock parts. Recently, with the school and weather, I haven't been able to ride it that much. Anyways, when I picked it up from the shop, the bars ...
6
votes
1answer
1k views

How to prevent the quick-release pin on the Tektro drop brake lever from rattling?

Tektro RL-340 brake levers have a quick release mechanism that, when pushed in, will lengthen the cable to allow to easily disengage the brake from the wheel/disc without needing to deflate the tire. ...
0
votes
1answer
138 views

Handlebar size options

I was given few options to choose the handlebar size for my future road bike. The frame size is 60cm but for the handlebar I have these options: 40x90,40x100,42x100,42x110,44x110,44x120 I measured ...
8
votes
4answers
835 views

After an accident, what next?

Cycling home in the dark a car pulled across me to enter a super market car park. Apparently the car that let him cross didn't remove their full beam so he didn't see me in the cycle lane and I hit ...
0
votes
1answer
198 views

Drop Bar for Lespo Frame?

I've been riding my Lespo single-speed since April, and been contemplating whether to change my handles to a drop bar: Any advice if changing to a drop bar will have a dramatic effect on my fitness ...
1
vote
1answer
401 views

Are cross brake levers with compact drop bar redundant?

I currently have traditional drop bars and cross (interrupter) brake levers. I like the interrupters and use them a lot. But I'm going to get a compact drop bar (FSA Omega Compact bar on order), and ...
3
votes
1answer
1k views

Does the diameter difference between road and mountain bike handlebars make some bikes incompatible?

I'm shopping around for a new set of handlebars, I want to give trekking bars (aka butterfly bars) a try. They're reasonably cheap so I'm willing to dive in as an experiment. I'm wondering though, ...