The tag has no wiki summary.

learn more… | top users | synonyms

6
votes
1answer
145 views

How are Prophete chains with built-in locks assembled?

I recently bought a 3/32" chain from Prophete, and despaired in the attempt to close it. The complex end of the chain looks like this: Now, at first thought, the slight groove (the one where you ...
4
votes
1answer
1k views

Split crown “race” possibly dangerous?

On some headsets which use a cartridge bearing in the lower assembly, the crown "race" is split. Also, I know a lot of people split their crown race for the ease of installation. Perhaps I'm overly ...
3
votes
1answer
360 views

installing a 700-18-23C tube on a bicycle

When installing a 700-18/23C tube, does the nut on the valve stem go inside the tire (unseen once the tire is on the wheel rim) or outside the rim (so it is seen among the spokes)?
3
votes
2answers
939 views

Tubular Glue vs Tubular Tape

I'm looking into going for tubular tyres and I'm new to this part of the world. As far as I understand there are two main options to mount the tyre: 1. Tube Glue which kind of a pain in the ass ...
3
votes
1answer
486 views

Is my disc brake caliper correctly mounted on the frame?

I have been in the process of upgrading my bike a bit. A friend of mine convinced me to upgrade my brakes from my stock Shimanos to some disc brakes. After having a look around and asking question, I ...
3
votes
2answers
6k views

Shimano 600 downtube shifter installation

I recently purchased some vintage 6-speed Shimano 600 downtube shifters. The package came with all the parts in a ziploc bag and it looks a bit bewildering. Any idea where I can find an installation ...
2
votes
4answers
698 views

Can I install caliper or cantilever brakes on a frame and set of wheels designed for disc brakes?

I have a 2008 Giant XTC 01 that came with disc brakes. Those brakes have been difficult to service throughout my time with the bike, now the pads on the back are worn out the fluid lines on the front ...
2
votes
3answers
400 views

Brake piece grinding against fork

This brake was installed on a fixed-gear that did not come with any brakes. The nut on one side rubs against the fork, and over time it rotates and presses the pad against the wheel. Here is where ...
2
votes
1answer
86 views

Problem setting up Shimano 5800 levers for the first time

This is my second attempt to setup a Shimano 5800 groupset from scratch. The problem on both bikes has been that downshifting worked to a point, but upshifting never works. The process isn't detailed ...
2
votes
1answer
450 views

When Installing chainrings which are pinned, how should I orient the chain drop prevention pin?

I'm setting up a double crankset with a new front chainring which is ramped and pinned. How should I orient the outer front chainring with respect to the chain drop prevention pin? Should this line ...
2
votes
1answer
1k views

How to install geneticbikes.com's chain tug to horizontal dropout with anti-rotational washer and hub gears?

I have 8 speed Shimano hub-geared bike. When I place the chain tug by geneticbikes.com, the black tud does not fit into the dropout. According to the thread, here, I can use one chain tug to the right ...
1
vote
2answers
996 views

Installation of the simplex SX410

The Simplex SX410 rear derailleur on my bike was dirty, so I got it off to clean it. Yet, now I can't quite seem to get it on again in a correct way. Specifically, I can't get the spring to be ...
1
vote
1answer
867 views

How tight should a threaded BB be?

I have an english-thread, octalink Shimano bottom bracket, and a new frame. The frame has been faced before painting. I am not sure the BB is compatible with the frame. When trying to install the ...
1
vote
1answer
283 views

Problem during installation of Rockshox Reverb Stealth product

I am following the SRAM official procedure on a very similar bike to the one reviewed. However, I am stuck at this part: unthread the hose from the remote's barb. I just can't. I am holding the hose ...
0
votes
1answer
130 views

How to install brakes with clamps that are too tight

I recently picked up a set of Avid DB1's and put them on my bike, but it was a bear to get them on. For background, they've got a split clamp that is similar to a seat tube where simple compression ...
0
votes
1answer
77 views

Help me setup my bike to my weird size?

I'm 6'6" but have very short arms for my height. Many guys 6'0"-6'2" will outreach me if standing flat footed. I have an XL frame, 2014 Raleigh Talus 29er comp. I feel great on it, but I feel like ...
0
votes
1answer
49 views

assembling brackets and front crankset: how many spacers and orientation

Recently I bought a Bull's Black Adder 1 26 Inch frame and quite some time ago got a present Shimano Deore Lx FC M-583 crankset (brackets included). I know they are not a perfect match, but still ...
0
votes
1answer
280 views

Is it possible to fit this Tioga Mc Groove saddle on my bicycle?

See images here. The bar the new Tioga saddle is mounted on is a bit thicker than the one the original (terrible) saddle is mounted on and won't fit as is. I can take the old saddle off its bar ...