Tools, parts, techniques, and procedures to keep your bike in working order. MAINTENANCE is not the same as REPAIR, a separate tag. Maintenance is what one does on a regular basis. Repair is what one does only when something is broken.

learn more… | top users | synonyms (2)

1
vote
1answer
111 views

How do I reassemble the rear gearing after fitting new tyres?

I have a Raleigh maybe 8 years old with shimano 15 gears. How do I reassemble the rear gearing after fitting new tyres? Everything seems to be in correct position but a small bolt with captive nut ...
0
votes
1answer
100 views

What exactly happened to my rear derailleur?

I had installed my front derailleur and was adjusting the high/low when I noticed my rear derailleur was hitting the spokes of my wheel. Suddenly, I saw a screw pop out and then my derailleur popped ...
0
votes
1answer
262 views

Rear V-brake pivots (cantilever studs) asymmetrical on Specialized Hardrock XC 2004 - how to fix?

This is a bit weird question. I bought a Specialized Hardrock XC used bike cheaply on e-bay. It had no front brake and the rear v-brake had different arms and was very dodgy. I thought I would able to ...
-1
votes
1answer
350 views

V-brake mount for caliper brakes

Is there an addaptor or mount that uses your V-brake mounts to allow a new fork without disc mounts that i have, to enable it to use caliper brakes, i try to avoid geting new brake levers, i figure an ...
4
votes
0answers
100 views

Fixing hydraulic disk brakes, what to check first?

I have a 10-year old bike, fitted with hydraulic disk brakes. The bike has been actively used for around 4 years only though. Recently, my brake levers started to have more and more "play" before the ...
3
votes
0answers
243 views

Disc brake pad and rotor compatibility

The SM-RT53 rotor should be used together with resin pads. If it is used with metal pads, the pads will wear out very rapidly. from Shimano BR M-416 disc brake manual Which rotors work well ...
1
vote
0answers
138 views

Can I swap Semi-Metallic brake pads for Sintered Metal Brake Pads?

I'm running disc brakes on my cyclocross bike with semi-metallic brake pads. I find that I'm constantly having to keep my rotors cleaned off to ensure optimal performance. I'm used to my mountain ...
0
votes
0answers
15 views

Why is it important to keep bearing sets when greasing a campagnolo hub?

In almost all cases where hubs are regularly serviced, bearings don't need to be replaced. The general consensus though is to replace bearings after so many thousands of kms. Many posts on the web say ...
0
votes
0answers
26 views

orientation of non rotating washers (Nexus 8-Speed Internal Hub)

The anti-rotating washers on my Nexus 8-speed internal hub axle are opposite to what every service manual I've seen suggest they should be. In particular, the yellow washer is on the left side and ...
0
votes
0answers
52 views

Where to buy 2005 Shimano 105/Ultegra brifter hoods?

I have a 2005 Trek 1500 WSD road bike with original Shimano 105 STI brake/shifter levers. I'm looking for replacement hoods for the brifters because the originals are wearing out. I believe the ...
0
votes
0answers
40 views

Planet Bike speedometer won't reset

I have a planet bike speedometer and after the winter season it seems that it is no longer functioning. It will come on when the bike starts to move but I cannot reset it and it seems to be frozen on ...
0
votes
0answers
122 views

How much grease on a coil suspension fork?

When servicing my SunTour XCR suspension fork, I happen to put about a handful of grease. On a factory-lubed fork I found out that they pout less that 1/10th of that ammaunt. The grease goes tot the ...