Repairing your bike when something is broken. REPAIR is not the same as MAINTENANCE, a separate tag. Repair is what one does only when something is broken. Maintenance is what one does on a regular basis.

learn more… | top users | synonyms (2)

1
vote
1answer
123 views

Rear wheel wobbles

my rear wheel wobbles while it spins, like in this video. I read in the comments that it could simply be a badly mounted tire. What's your advice on this, what should I do?
5
votes
1answer
697 views

Pressure gauge on my pump stuck at one value, what is wrong?

I have a Specialized Switch Hitter I have used for several years on both Presta and Schrader valves. Recently, my wife tried to inflate her tubes (Schrader valve) and could not get the pump to ...
4
votes
1answer
3k views

Upgrade/Replacement options for Cannondale Headshok DD50?

I have an older Cannondale that I love. It's an F600 comp (the special edition one in pumpkin orange), with a DD50 front shock. The problem is that the DD50 is WORN as all heck. Even when locked ...
8
votes
5answers
701 views

Fix / clean or throw away tire with 30+ thorn punctures?

I recently rode through a horrible thorn patch. I came out with 2 flat tires. Upon examination, I found that the tube was punctured in 10+ places. Throw away. The tire has 30+ small thorns in it. ...
0
votes
1answer
586 views

Can't get the drive side bottom bracket cup out

I have an older Raleigh frame that I converted to a fixed gear and the bottom bracket cup on the drive side has been painted over a few times and I can't get it out. This is the type of cup (the one ...
3
votes
3answers
460 views

What are the most common causes for hysteresis in the rear derailler?

I have often seen derailleurs on cheap MTBs to degrade in performance by showing hysteresis. By that I mean that to switch to a certain cog, one needs to shift one cog further and then immediately one ...
0
votes
1answer
156 views

Caliper bolts after crash: repair or replace?

A few days ago, I was looking down checking out my crank while riding and drifted into the LA River Bike Path and ended up crashing bending my front brake caliper. Can the recessed bolt that holds ...
1
vote
1answer
221 views

Spoke tension - is a left tilt ok to prevent explosion?

The left hand steel blade spokes of my WH-RS30 (not 30A) are constantly exploding inside of the nipples when going up hill in a standing position. I have increased the right hand side tension to about ...
0
votes
1answer
769 views

repair scratches on surly frame

I am a happy owner of a Surly Cross Check frame, two years old. Today I put it against a pole, but a strong wind blow made it slide along the pole and fall to the ground. As a result, there is one ...
1
vote
2answers
609 views

Bottom bracket cup doesn't fit on non drive side

I'm replacing the crankset and bottom bracket on my old steel frame road bike, which looks like this one, so I'm guessing it's from around 1985. I picked up a 68 mm square taper bottom bracket and ...
3
votes
2answers
887 views

How can I remove the bottom bracket from this old road bike?

I need some help removing this bottom bracket. I am obviously no mechanic, and watching several videos on youtube I found nothing that could help in this specific case. Basically after removing both ...
2
votes
1answer
566 views

What tool is needed to adjust this headset on a children's bike?

My daughter's bike has a threaded headset, and I don't know what tool I need to adjust it. As you can see from the picture, there are the following parts in the stack: a knurled ring, which ...
-1
votes
1answer
153 views

I'm worried about my derailleur snapping. The chain isn't running around the bottom pulley, it's running next to it

I'm worried about my derailleur snapping. The chain isn't running around the bottom pulley, it's running next to it, scraping against the bottom pulley and the frame. When I change gears it makes a ...
1
vote
2answers
5k views

How to fix a stripped pedal crank

The threads on my bike's pedal crank just became fully stripped and the pedal fell off, though the pedal itself is fine. Is there any way I can fix this without fully replacing the pedal crank?
3
votes
1answer
203 views

How to replace a tube with only one quick stick?

So what is the correct number of quick sticks to swiftly change the tube? I had always thought that the answer is of course 2, but : I can do it twice as fast with one Quik Stick as you can with a ...
3
votes
1answer
121 views

Rim cement as a replacement for rubber cement

Can I use aluminium rim cement for patching flat tire instead of using rubber cement?
5
votes
3answers
1k views

Cost of maintenance of a roadbike

I am going to buy a bike and ride upto 1000 km or more in a month. Adding them, I think it will come to 12 k to 15 k per year on an average. I will be riding on highways, so there won't be any ...
1
vote
1answer
649 views

Is there any replacement for the chainrings of a Shimano STX crankset?

I have a Shimano STX Crankset (probably FC-MC series or similar, around 2001) with worn out chainrings (5 Arms). Is there any contemporary replacement opportunity for either the chainrings or the ...
13
votes
7answers
2k views

What tools on a multi-tool do I actually need?

I feel like there are almost as many bike multi-tools out there as there are bikers. In a single trip to REI, I found nine different bike tools each ranging from only four to over thirty individual ...
3
votes
2answers
845 views

Rear derailleur and front shifter are not indexing “together”?

So my rear derailleur and front shifter have stopped working together, my shift can shift once up and then nothing. My bike has essentially turned itself into a 2 speed. The shifter is a 2300 shifter ...
1
vote
1answer
357 views

FC-M330 replacement

I have a Trek 4500 with a Shimano FC-M330 crankset. I need to replace the crankset and was hoping that someone could tell me the current replacement. I believe that I have narrowed it down to the ...
1
vote
1answer
96 views

Is it ok to use a 9spd link on a 10spd chain?

I accidentally broke the master link (a.k.a reusable missing link) on my 10psd KNC x-10 chain. Since I only had a SRAM 9spd replacement link, i used that to connect the chain. I rode 30 Km without any ...
4
votes
2answers
906 views

What is the largest hole a tire can bear before replacement?

Saw this question today. The tire in question has a 2cm long hole on the inside, from a knife. I sometimes get puncture flats from e.g. glass. Never as big as 2cm. Usually if they're less than ...
3
votes
3answers
142 views

How to repair shifter housing

I have shifter with damaged housing. It shifts well, but I guess if housing is not repaied, rain and elements will quickly put an end to it. Which material would be suitable to fix this hole? Epoxy ...
1
vote
1answer
432 views

Can I replace a 1/2 inch bolt with a 14mm one to secure my axle?

My front wheel is secured with 14mm bolts, while my rear wheel uses 1/2 inch bolts. Turns out my multitool has only a 14mm wrench, so I can't change the rear tire with it. Rather than carrying ...
3
votes
1answer
946 views

Rear internal hub won't shift gears

I have a 1963 Sears cruiser, three speed, which I bought very recently. On my third ride, the middle speed stopped working, and went loose; there wasn't any "traction" when I pedaled. It happened as I ...
2
votes
2answers
290 views

Fixing Carbon Fiber

I have a Cervélo S2 and absolutely love my bike. It has been rock solid. Unfortunately, I had a bad case of chain suck when my chain fell off my chain ring right when I was grinding up a hill. The ...
0
votes
5answers
993 views

How can I repair a swollen tire allowing visibility on the inner tube (picture provided)?

I have a new problem on my bike which occured after patching my inner tube. Since I put the patch on, my tire is pushed out away from the rim near the intake valve (not near the patch). In the picture ...
2
votes
1answer
213 views

Size of Pedal Threading on old German Glockenlager?

I removed the pedals of a Göricke bike from 1934 or 1935 (according to the bike number). It has a Glockenlager (What is that in English? Bell shaped bottom bracket?) as seen in the picture. The crank ...
4
votes
1answer
853 views

What to do about a stuck chain link on 10 speed chain

I put a new chain on my bike and after 3 rides or so, I developed a stiff link. I'm not sure what caused the issue, but now it barely bends at the pin at all, unless forced. It causes skipping ...
1
vote
2answers
1k views

Are aluminum or steel chainrings more resistant to bending?

I mash a lot and wind up killing chainrings. I later find that my chainring warps at the midpoint between two chainring bolts. Usually my first sign that something is wrong is my chain pops off or ...
3
votes
2answers
3k views

Can I use a shock pump to inflate a tube?

I know that shock pumps are meant for high pressure applications so that they can withstand high pressures needed by suspension shocks. However, can I use a shock pump to inflate my tire in a pinch ...
6
votes
4answers
3k views

How can I properly replace the hose on this older Schwinn pump?

I have the following Schwinn bike pump. It’s pretty old, perhaps 30 years or more. I like it a lot. Some years ago, I changed to Presta valves; for this I needed a new head. I got a Topeak ...
1
vote
3answers
262 views

Refitting Cable to Rear Derailleur

Whilst riding recently the cable slipped from the clamp on the rear derailleur. I'm attempting to affect repairs by re-clamping the cable. However by pulling the cable tight I have lost the bottom 2 ...
3
votes
3answers
2k views

Shimano Hollowtech left crank arm getting loose

After 2 years of good use, left crank arm on my FC M542 crank set has started to get loose quite often (cca 500 km). It is usually indicated first by few now an then click-clanks somewhere in the ...
4
votes
1answer
489 views

Should cassette “wiggle”

Recently My freehub broke and so I removed the cassette to replace the freehub and noticed, whilst off the bike, 4 of the remaining bolted together 8 sprockets wiggled (4 wiggled together but ...
7
votes
6answers
9k views

How can I tell if a rim is bent or if the wheel is just out of true?

How can I tell if a rim is bent or if the wheel is just out of true?
4
votes
3answers
2k views

how to repair large holes in inner tubes

I find that any hole, cut or tear larger than a pinprick is impossible to repair with normal patches because they are too soft. Even a 2-3mm slit will cause the repair patch to balloon out and burst ...
2
votes
1answer
877 views

How do I re-attach a crank that has fallen off?

I have already read My crank fell off, how do I re-attach it?, but it did not answer my question. I was biking up a hill in first gear, and I felt my left crank was a bit loose. Never having had ...
7
votes
1answer
250 views

Do I need to get a replacement bike for this broken chainring?

I wanted a cheap commuter bike, and just received this bike from Amazon. I have little knowledge about bikes, but looks like the middle chain-ring is broken to me. Is this indeed broken, or is it ...
4
votes
1answer
2k views

How to reassemble spring assembly on Shimano M520 SPD pedals

I have a pair of shimano m520 pedals which were damaged in an accident. The springs rotated past the tension bolt and now the back section, usually under tension, now hangs free. How can I ...
2
votes
3answers
710 views

Failing to unscrew BB - what now?

I have an external bearing BB, that I need replaced (It is quite badly rusted). I opt to do the repair myself. The bike is a Specialized Hardrock, the crank arms are SR Suntour. Having removed the ...
2
votes
5answers
1k views

Six speed chain on an eight speed bike

So in the shop they asked me "what chain do you need" and I said 7. They said "you could try this 6-speed, it is half the price of a 7, and we put it on 7-speeds all the time". I said "ok", only to ...
3
votes
3answers
1k views

Front derailleur sticking, not shifting. Will soaking in solvent damage parts?

I've got an older deore lx front derailleur for a mountain triple crankset. It wasn't shifting properly, and it seems that it's sticking and not returning back to a neutral position when I shift it. ...
8
votes
3answers
346 views

There is a lip on my brake pad from bad positioning. Can I remove the lip?

One of my bikes had the brake pads positioned poorly and they developed a pretty pronounced lip where the pad hung off machined braking surface on one side. The bike is using cantilever brakes. These ...
12
votes
2answers
5k views

Is it possible to repair a dent on an aluminium frame?

I have Centurion Cyclo Cross 4000 bike. Recently I got into an accident with a car door. As a result I have a significant dent on my frame(see the photos below). I have two questions: Is it ...
4
votes
2answers
2k views

how do you make a chain longer with a simple chain breaker?

I was replacing a chain and managed to cut the chain too short. Is it possible to make the chain longer using a simple chain breaker? If so, how?
2
votes
2answers
9k views

How do I determine the model of my Shimano Rear Derailleur?

I recently damaged my rear derailleur and am trying to find the replacement online. It is a Shimano Tourney SIS Index. I have found several models in the Shimano website that are pretty close ...
-1
votes
2answers
243 views

the derailer is touching chain and it won't let me go past 14 speed supposed to go 21 speeds

The derailer on my 21-speed bike looks like it's bent. It won't let the chain go onto the 3rd ring of the front derailer so, no I can't shift past the 14th speed. If I try it makes a loud sound, like ...
2
votes
3answers
848 views

How exactly are pedals attached to crank arms?

Recently I tried to unscrew the left pedal of a bicycle by turning it counter-clockwise with a spanner lengthened with a piece of pipe. The net result is the spanner broke apart and the pedal is still ...