2
votes
2answers
76 views

Rear mech cage stuck, how can I take it apart?

This is a shimano ultegra 6700 rear mech. The swing arm/cage is incredibly stiff where it connects to the derailleur. I can just about rotate (red arrows) it a small amount but requires a lot of ...
3
votes
2answers
133 views

Are Shimano components compatible with each other? Do I have to get a specific chain?

My cycling maintenance experience goes as far as changing tyres, but winter has been cruel and I need to replace some components. Setup: Cassette is a Shimano 105 CS-5700 Front chainring : Shimano ...
3
votes
4answers
3k views

How to repair sticky Ultegra shifter

I have Ultegra 3x9 shifters and derailleurs that were installed just a couple months ago. I purchased them on eBay and although they were new, they had been sitting in inventory for a couple years so ...
2
votes
2answers
1k views

How should I lubricate my Shimano freewheel?

I have a Shimano freewheel (MX-30) that came with my bike from new. Unfortunately the internals got all gunked up and it stopped working (never engaged and became free both ways). I have bought and ...
1
vote
1answer
539 views

Can I use 10-speed Shimano STI shifters with a 9-speed drivetrain?

I need to replace Shimano 105 STI shifters on a 9-speed road bike which was damaged in an accident, however there are few places that still stock 9-speed Shimano 105 STI shifters. Can I use the ...
3
votes
1answer
1k views

How do I clean the inside of a freehub?

I didn't know any better and I let degreaser drip into the freewheel body of my Shimano FH-RM65. Now it makes a terrible retching noise when it rotates. How do I clean the inside of this thing? ...
3
votes
3answers
6k views

What tool is needed to remove a Shimano HG-50 freewheel?

What tool is needed to remove a Shimano HG-50 freewheel from the wheel hub? It looks like a 12mm or 13mm Allen key. Will this do it or is there some detail I have missed?
1
vote
3answers
1k views

Ultegra 9-speed brifter upshift problem - beyond WD-40?

I have a 2000 Ultegra 9-speed right/rear brifter that does not "release" the cable properly. My initial search on this problem suggested that this could often be cured by flushing with WD-40. So ...
2
votes
2answers
4k views

How do the adjustment barrels on a gear cable work?

I have a Shimano Sora derailleur on the bike I just bought with a triple chainring in the front. Right up by the shifters there is a sort of barrel adjuster on the cable. It doesn't seem to do ...
3
votes
1answer
864 views

Are Shimano Hollowtech II bottom bracket spacers unique?

I'm moving my Shimano Hollowtech II XT crankset and bottom bracket over from a bike with 73mm bottom bracket to a 68mm bike. The only problem is that I only have 1 spacer and now I need 3 bottom ...
6
votes
4answers
2k views

Trouble getting the right cup and cone hub adjustment

I have a pair of Shimano XT wheels and recently had issues with the hub on the rear wheel requiring new cones and bearings. These were fitted carefully but I've had issues getting the right adjustment ...
2
votes
6answers
5k views

Adjusting rear derailleur - shifts to lower gear, but not to higher

Well, it will shift to a higher gear, but it takes two clicks of the shifter and it skips over a gear when it does shift. With one click the chain hangs on the current gear by the slimmest if threads. ...
14
votes
6answers
10k views

Does this chainring need to be replaced?

Here is a closeup of my triple: All three rings are Shimano Ultegra and have never been changed. They probably have at least 12000+ km on them. I've been pretty good about changing the chain ...
6
votes
3answers
2k views

What kind of maintenance does a shimano dynamo hub need?

I have a shimano dynamo hub on the front of my bike. Does it need any special maintenance, or maybe it needs just a little synthetic grease once a year, like a normal front hub?