The stem is the part of the bicycle that secures the handlebars to the fork.

learn more… | top users | synonyms

0
votes
1answer
23 views

Stem diameter question

Changing to an adjustable Ritchey stem on my Trek 7.3. My bars are 25.4 and the stem I'm looking at is stated to be for 25.8-26. With this being half a millimetre bigger, will it still fit ok? Many ...
12
votes
1answer
5k views

How is stem length (reach) measured?

How is the length of a stem measured? Where does the measurement start and finish?
5
votes
4answers
156 views

Creaking when in the saddle

I know there are about a million questions on here about creaking while pedaling, but I haven't seen one that relates...apologies if I missed one. I bought a 2011 BMC Streetracer SR02 last year; ...
0
votes
0answers
59 views

Is a long, high angle stem safe to use with a carbon steerer?

I purchased a hardly used road bike someone else had built up for a deal a few weeks ago, and am a bit disappointed with the fit - it's fine for rides less than a couple hours, but too aggressive for ...
6
votes
1answer
285 views

How does a quill stem without a front bolt work?

Looking at quill stems I noticed this rather curious one and I couldn't imagine how it secured the handlebars without an apparent bolt. Any ideas? more images
1
vote
1answer
52 views

Adjustable stem issue

Hello I have a quill adjustable stem on a Raleigh Royale. (The bike is an absolute dream to ride, wonderful seat and great gearing) My issue is that the handlebars wobble, both front and back and side ...
2
votes
2answers
52 views

French handlebar fit

I have an Atax stem ('85 Peugeot). Original steel handlebars are 25 mm. Is it prudent to spread the stem to accommodate Nitto 25.4 randonneur bars?
2
votes
3answers
468 views

Replacing mountain bike bars & stem with drop bars

I have a mid-1990s Specialized Rockhopper. I've trashed the flat bars that were on it previously and I want to install drop bars, but to make that comfortable for me I'll want a shorter and higher ...
1
vote
3answers
779 views

Pedals hits the ground too often while turning at relatively high speed

I’ve been riding for 40+ years of which the last 25 I’ve ridden Specialized. Around April last year I decided to replace my old bike with a brand new Sirrus Sport, on an XL frame. While I love the ...
1
vote
3answers
238 views

Should I be able to 'manually' rotate the headset?

When I wrap my fingers around my roadie's headset, I'm able to 'rotate' some parts of it freely around. Should this be happening? If it should not be happening, what is causing this and is it ...
5
votes
4answers
1k views

Bike is slightly too large, shorten the stem?

I feel that my bike frame is slightly too large because I'm stretching out quite a bit even when on the hoods. I'm considering swapping out my 90mm stem for a 35mm or 40mm stem It seems like these ...
1
vote
1answer
300 views

Combining flat bar and aerobar: Double stem setup or alternatives?

I'm currently running a pair of clip-on aerobars (Syntace C2) on my long distance touring bike. I've set the aerobars up quite high, as for me they are not so much about the aero-part (though it still ...
0
votes
1answer
82 views

Can I use a 1“ stem on a 1 & 1/8” steer tube?

I have a Nitto Technomic stem that I'd like to use on a '92 trek 930 with the idea of converting it from a mountain bike to a poor man's expedition touring bike with drops. I found this shim that ...
4
votes
7answers
4k views

Is reversing the stem (pointing it backwards) a safe way to reduce reach length?

Assuming a steerer/fork/brake/cable setup that does not rely on the stem facing forward: is it safe to point a stem backwards as a way to reduce seat-to-bar reach (i.e. as a way to 'fit' a too-large ...
7
votes
3answers
2k views

Is it safe to use a spacer that reaches above the steerer tube?

I have a spacer that reaches from the top of the stem and over the top of the steerer tube. I am able to lock it down with the top cap, but I was wondering if it is safe to ride like this, or if I ...
1
vote
1answer
167 views

Can´t remove BMX stem top cap bolt (won´t loosen)

I was trying to remove the handlebar and stem of my bike in order to be replace them. The bike has got a BMX stem and the top cap bolt is spinning freely in both clock and counterclockwise. Any idea ...
5
votes
2answers
4k views

What's the performance difference between a front-load and top-load bike stem?

I recently bought a bmx and after doing a few tricks on it, the front-load stem became loose enough for the bars to slide forward (they rotated towards me about the point the bars were connecting at ...
14
votes
5answers
2k views

Deterrents against partial (component) theft

Big question: Is there any way to increase the security of bolted on portions of a bicycle? Specifics: I cycle as my primary mode of transport (in East London) on a early 90s steel road bike with ...
3
votes
4answers
4k views

Getting the right cockpit position. Sliding forward. What should I adjust to keep my sit bones on the seat?

I am experienced rider and I'm looking for some advice on how to adjust my cockpit position. I am a daily commuter, and do regular 40-50k rides on the weekends, and with the warmer weather will work ...
3
votes
2answers
210 views

torque specification on headset

I was wondering why there is a torque specification on the steer tube end of the stem for mountainbikes. The torque specification that goes to the handlebar is reasonable, after all handlebars are ...
3
votes
2answers
1k views

Handlebar stem : height vs length

I want to decrease the reach of my handlebars. Does it matter whether I increase the height or get a stem with a smaller length(extension?) on my bike? And is there any way to calculate the ...
2
votes
4answers
3k views

BMX stem slipping; how to stop?

I recently bought a BMX bike that currently has all stock parts. Recently, with the school and weather, I haven't been able to ride it that much. Anyways, when I picked it up from the shop, the bars ...
2
votes
1answer
161 views

Replacing stem on non-oversize bars

I have a road bike from Circa 2003 and it currently boasts an ITM Millenium stem. The stem is a bit long for my liking at around 130mm and I was thinking of replacing it with a shorter one for a ...
0
votes
1answer
117 views

What could be the reason for stem this far away

I own a bicycle similar to this one: (I replaced the handlebars with straight one on mine) I know that there were some weird designs back in '90s, but some reason probably exists for creating a ...
2
votes
2answers
783 views

Dropped the Wedge of a quill stem in the head tube

Trying to remove a seized quill stem and did a beginner's mistake of removing the stem bolt. I could not thread back the bolt. Is there a better way to thread back the bolt to the wedge for me to ...
1
vote
2answers
292 views

Screw cap stuck in adjustable stem connection, how to remove or reattach?

I was trying to detach my handlebar, because lowering was insufficient to make my bicycle fit in my box. I detached the long screw going connecting two lids thereby fastening the stem-handlebar ...
5
votes
2answers
4k views

Is it possible to compensate a short sized frame by adjusting seatpost and stem?

Could you achieve the same position you would have on a bigger frame by raising seatpost and stem? And how could I adjust those to "simulate" a bigger sized frame?
3
votes
2answers
785 views

New stem, bars & shifters on old Bridgestone 700

I recently bought a 1980's Bridgestone 700. I have trouble feeling confident on this bike between the narrow drop bars and the downtube shifter. This is my all-steel commuter and I'd like to put ...
3
votes
2answers
784 views

What would be the handling of a bike with reversed stem?

There are short and long stems: What effect does changing the stem length have on my bikes handling There are flat bars and there are curved back bars for comfort upright position: There even ...
4
votes
2answers
179 views

Installation of a shorter stem

I want to install a shorter stem onto my mountain bike, can I just swap them out or will I need to get the star nut replaced or reset?
3
votes
1answer
1k views

How do I remove a quill stem?

(I recently got an old Favorit road bike (made in Czechoslovakia) and started restoring it. In order to give the frame a new coat of paint, I need to strip it down from everything.) I'm stuck with the ...
2
votes
2answers
888 views

Is there a difference between mountain and road stems?

I see them advertised as being good for one or the other. Is there really a difference? Or is it just a marketing gimmick?
3
votes
3answers
3k views

How do you make the handlebar stem straight?

I adjusted my stem height the other day, and since then, the stem hasn't felt straight. I've attempted to straighten it a few times, but because I'm just eyeballing it, the handlebars don't quite seem ...
1
vote
1answer
423 views

Long Quill Stem?

I picked up a used mid 1990s Serotta Colorado CSI (lugged steel) bike. It is a size 54L which in Serottas from that era means it has a 54 seat tube but a 55 top tube. The size was not intentional, it ...
1
vote
2answers
495 views

Upgrading my cockpit- brakes, stem and bars for longer reach

I want to upgrade my cockpit so that I have a longer reach. I currently use it as my city bike. Its an old vintage HR bates frame. Currently the stem is a little short. I want to change the bars - ...
2
votes
2answers
258 views

Rust proof or not the outside of a steel steerer column beneath the stem

I have a new steel frame which I am building up. I intend to rust proof this first by using Waxoyl made by Hammerite which I will use on the inside of the frame and forks. Should I use this on the ...
2
votes
3answers
2k views

Do all stems have the same stack height for the steerer tube clamp?

Does the height of the steerer tube clamp differ between stems, or is there one standard height used on all modern mountain bike stems? In my particular case I want to replace the stem on a mountain ...
3
votes
1answer
2k views

Is it possible to replace a 1 1/8 steering tube with a 1"?

I have a 94 Giant ATX. Threaded 1 inch steeering tube. I need a shorter stem, and would also like to install a suspension fork. Is it doable? Could I take a modern suspension fork, heat the crown, ...
4
votes
1answer
1k views

Geometry between 50mm stem and a 65mm stem and riding experience

Will I notice much difference beside just having a slightly longer cockpit between my seat and fork if I upgrade from a 50mm to a 65 mm stem? is this 15mm a significant enough adjustment to make my ...
4
votes
2answers
257 views

What brand is this handlebar stem?

I just purchased a used bike recently and I am curious to the make of my handlebar stem. Would anyone be able to identify the brand logo?
4
votes
2answers
946 views

How deep does a quill stem need to be inserted?

I have an old road bike with a quill stem and I want to raise the stem. After raising it to where I want it, the stem has about an inch between the high end of the expander nut and the top of the ...
3
votes
2answers
252 views

Front wheel getting misaligned while climbing hills

I've got a single speed bike with bullhorn handles. When I'm climbing steep hills I pull on the bullhorns quite hard, and once I'm back on a flat I'll occasionally find that the front wheel has become ...
2
votes
1answer
4k views

Measuring stem clamp / handlebar diameter

I have a new-ish Bianchi Cortina hybrid that I'm trying to find suitable drop bars for, but I can't figure out the proper size to get. It seems like the bars mostly come in 25.4mm, 26mm and 31.8mm. ...
8
votes
3answers
6k views

Attaching a stem to a carbon steerer: how much torque?

So I decided to travel with my bike this week and to my surprise discovered that the steerer is carbon fiber. I had removed the stem from the steerer for packing but naively assumed it was aluminum ...
2
votes
2answers
2k views

How can I move the handlebars on a mountain bike close to the rider without affecting handling and control?

I recently finished building up a mountain bike, with the help of a friend. My initial rides - a few miles, nothing too extensive yet - revealed that I need to move the handlebars a bit up and back ...
2
votes
2answers
453 views

how much can i raise my stem?

I've got one of these stems: It's currently fully inserted into the bike, and it's too low for me. Can I simply loosen it, raise it 5cm and tighten it again? What's the minimum length that ...
4
votes
3answers
20k views

Better solution for uncomfortably low bars: a stem riser, or taller stem?

I've got my (threaded) stem at the maximum height, but I'd be more comfortable if the bars were higher relative to the seat. It would be uncomfortable to lower the seat any further. I was intrigued ...
11
votes
1answer
6k views

What effect does changing the stem length have on my bikes handling

I'm finding that when jumping my mountain bike seems to be very nose heavy no matter how far back my saddle is. What effect will moving to a shorter stem length have? My bike, a Boardman FS-PRO came ...