5
votes
1answer
303 views

Truing an 'out of round' wheel

I am building my first wheelset. The front wheel went without a hitch - nice and true both radially and laterally. However, the rear wheel has a pronounced (5mm) bulge over about 1/4 of it. The ...
2
votes
1answer
153 views

When turning a corner my rear wheel touches the brake pad, is this normal?

I replaced my brake pads about a week ago and today I noticed that, when turning (or generally under lateral force), the rim touches one of the brake pads (depending on which way I'm turning. I ...
1
vote
1answer
126 views

Can I mount a wheel with a narrow hub to a wide frame?

Suppose I have a 120mm hub with a long axle, that I want to mount in a frame with 130mm dropouts. In principle, it seems to me that this should be fine, but I want to confirm this. One immediate issue ...
6
votes
1answer
173 views

Spoke Tension Guidelines

Generally what should the tension be for spokes in wheels built up from scratch? For the front wheel? Should the tension be different for drive-side/non-drive-side spokes in the rear? Should tension ...
5
votes
3answers
349 views

What tolerances should I use for spoke tension when building a wheel

I am replacing the rim on my rear wheel with a new one. I've brought up the tension on the spokes close to the final tension by truing / increasing tension / truing / increasing tension. I've got ...
3
votes
1answer
998 views

How do you install a hub dynamo?

I want to buy a Shimano hub dynamo, but I'm encountering problems getting a bike shop to commit to installing it for me if I buy it. So I have a couple questions that I'm hoping some of you guys might ...
0
votes
1answer
314 views

Are shimano FH-2200 hubs strong enough to use in a tubular wheel for CX racing?

I have a pair of Shimano FH-2200 front and rear hubs lying around which I no longer use and I would like to save money by using them for a wheel build but am unsure whether they would be up to the ...
2
votes
1answer
138 views

Aero spokes strength on a family bicycle

I am building a new wheel for my family bike: there will be a kid seat on the back rack over the wheel. I picked up some cheap double butted flat aero spokes (not elliptical but flat). From reading ...
1
vote
1answer
226 views

rebuild shimano wheel

I've dented the rim on my Shimano WH-RS-10 rear wheel. I found the tech doc pdf. I've had wheels rebuilt before but always with rims that were available to consumers. I can't find any place that sells ...
3
votes
2answers
414 views

lacing Alfine wheel, trailing spokes inside or outside hub flange

I am about to lace an Alvine hub wheel. Reading Sheldon Browns article there is a suggestion that the trailing, and so key, spokes might be better laced the opposite of what would be done for a ...
2
votes
2answers
1k views

Can I run a wheel with a 130mm hub on a mountain bike with 135mm spacing?

I'd like to build a wheelset that would work on my cross bike or my 29er, assuming I had disc brakes on the 29er and rim brakes on the cross bike, is there any way I could use a 130mm hub (that fits ...
1
vote
3answers
756 views

Are velocity A23 rims suitable for building a wheelset for a 29er Mountain bike?

I'm was looking to build a new wheelset that I can use on my rigid Karate Monkey 29er using either cyclocross or Trekking tires for gravel / dirt road riding and 29er tires for singletrack (mostly ...
5
votes
3answers
2k views

Do I need a separate dishing tool for building wheels with park tool TS-2.2 truing stand?

I'm trying to get started with some wheelbuilding. I've got a Park Tool TS-2.2 truing stand. Can I just rely on the calipers to provide a guide for centering the rim and dishing rear wheels or will I ...
20
votes
5answers
1k views

Spokes keep breaking - bad hub or bad build?

Background information A bit of background information (I'll try keep it brief): Last year I bought an old but unused bike, 5 speeds with internal gearing. Apparently the shop bought a lot of bikes ...
3
votes
1answer
286 views

How much does nipple choice affect wheel weight/stiffness?

Would I be a fool to replace the nipples on a Dura Ace 7900 C24 wheelset with a set of DT Swiss anodised alloy nipples, in the interest of aesthetics? I want the bike to look nice, but don't want to ...
2
votes
2answers
817 views

Tensioning rear wheel?

Tensioning a front wheel is - at least in theory - very simple: Go around and tighten each nipple by e.g. a quarter turn. Then re-adjust trueness if necessary. I guess if I'd do the same to a ...
6
votes
4answers
2k views

How effective is checking spoke tension by ear?

Sheldon Brown's Wheelbuilding page links to the article: Check Spoke Tension by Ear. Obviously a tensiometer would be ideal, but Sheldon suggests that checking spoke tension by ear is a reasonable ...
-2
votes
1answer
1k views

What alternative spoke lacing patterns exist (that make a decent wheel)? [closed]

I'd like to know of all the 'normal' ways to spoke a wheel. Currently, if you want to use a non-standard pattern, you have to run the length computations a number of times; for example, in a 3-spoke ...
3
votes
3answers
2k views

Can I lace my hub with all inward or outward facing spoke heads?

It seems conventional wisdom says to alternate inward vs outward spoke heads going around the flange when lacing a wheel, like this: However, I'm wondering what the reason for this is, and if it ...
2
votes
2answers
1k views

Oil/Anti-seize on outside of nipple when building a wheel?

I just took apart my old wheelset which let some delightful snaps out as I loosened the nipples that were seized to the rims. I'm wondering what the benefits would be of a small amount of anti-seize ...
7
votes
3answers
3k views

Why offset the rear rim to the hub and not the hub in the frame?

I'm currently reading The Bicycle Wheel by Jobst Brandt, and I'm reading all of the issues with offsetting the rear rim toward the drive side of the hub... Asymmetry in a rear wheel built for a ...
5
votes
10answers
6k views

What should I use, VeloPlugs, Rim Tape, or Rubber Rim Strips in new wheels?

I'm building two new sets of mountain bike 26" wheels, and I'm wondering what to go with. Both are double walled rims, so in addition to the standard rim tape and strips, I can use a product like ...
6
votes
2answers
3k views

What are the pros and cons of Double Butted vs Straight Spokes when building a wheel?

Straight spokes will have the same diameter through the whole length, double butted spoked are thinner in the middle than at the ends. Here's my current understanding of the benefits of each: Double ...
0
votes
4answers
2k views

Which spokes to get, Wheelsmith or DT Swiss Spokes?

I'm building two sets of 26" wheels, one pair of 32h triple cross with Bullseye hubs with machined sidewalls for rim brakes, and another pair of 24h double cross with Alex A-Class hubs with Sun rims ...
3
votes
6answers
770 views

How to build a wheel

I'm in the planning stage of building a new bike. This will be a light road bike for city runs and transport. For racing I have other bikes. I'd like to build the bike from ground up by assembling ...
4
votes
2answers
506 views

What are wheel tension relief machines called?

At a San Diego bike shop I saw a machine that is purported to take the tension out of a wheel while it's being built so that the tension won't be released when you first start to ride it. ...