The chain keeps wanting to load towards the right hand side of the cog no matter how I orientate the chain. This causes painful skipping. Do the marks have anything to do with it?

I have a singulator and I've moved this left-right and even removed it but i still get the same issue: chain loading towards one side and skipping.


  • 4
    If you could post a photo TAKEN BY THE SIDE (lateral view), it is more important. Dec 12, 2012 at 18:11
  • will do tmrw...
    – colmcq
    Dec 12, 2012 at 21:38
  • From that angle the cog appears to be worn out, but a side view would be more convincing. Dec 21, 2014 at 15:09

2 Answers 2


Your chain skipping/dropping could be the result of a few things, so I'll lay them out briefly:

  • Your chain/freewheel could be worn out. If you recently replaced your chain, the worn out teeth of the freewheel won't mesh with the new chain and will cause skipping. Simply examining the profile of the freewheel teeth with pictures of a new one will give you a sense of whether this is a possibility. (Worn out teeth are sharper at the tops and, in serious wear, form little waves or shark-fins.)

  • It is possible that the chain installed is too narrow for the freewheel teeth (though it would be a very noticeable problem.) Muti-speed chains are typically 3/32" wide, while some single speed chains are 1/8" wide. Freewheels are manufactured in both widths. Where one can run a 1/8" chain on either width freewheel, a 3/32" chain will bind noticeably on a 1/8" freewheel.

  • The singulator installed on your bike may not be providing enough chain tension. The actual alignment of this component won't cause the chain to skip as it it on the slack side of the chain. This is an unlikely scenario but could occur if it has been in service for a while or damaged in some way. Replacing the spring will bring it back to original tension specs.

  • The most likely thing I can imagine is that your chain-line is off. Your chainring is set further out from the center-line of the bicycle than the freewheel is, causing it to catch on the freewheel teeth and be thrown off. If the bicycle is a homebrewed single-speed, chances are you reused the original crank and bottom bracket spindle that were designed for a multi-speed bike. If this is a store-bought bike, it wasn't set up properly. Here is Sheldon Brown's article explaining the chain-line and how it is adjusted. In a nutshell, you will use different BB spindle lengths, BB spacers, and/or chainring spacers to line up the chainring with the freewheel. This can be done easily if you have the right tools and some patience. Here is a SE question relating to adjusting chainlines. Good luck!


  • you know what..I crashed last month. Now, while the chain didnt skip after I think its set the front chain ring off at an oblique angle...so no matter where i align the rear cog its always gonna be misaligned...
    – colmcq
    Dec 12, 2012 at 21:40
  • @WTHarper Just a more or less mathematical question: 3/16 is to my knowledge bigger than 1/8, right? How can then a 3/16" chain not fit on a 1/8" chain but not vice versa? shouldn't it be the other way round? Dec 13, 2012 at 7:36
  • 1
    He means 3/32" for the multispeed chain which is, of course, less than 1/8"
    – user5697
    Dec 13, 2012 at 8:32
  • the frame is frigging all squint and bent out of shape! didnt see that one till today.
    – colmcq
    Dec 13, 2012 at 16:07
  • Yes I did mean 3/32"! My brain was not in SAE mode, apparently.
    – WTHarper
    Dec 13, 2012 at 17:47

almost the same by me just i found the problem and it cuold be the same for yours one of the links from the chain is bent out of shape (use a flat screw driver to bend it back in shape)

  • Welcome to Bicycles SE. We're looking for answers with more detail. A short one-line answer like this is likely to get downvoted by the community and possibly deleted. You will also note on the help page that I have linked that we ask that you write to the best of your ability on this site. Please use proper sentence structure and punctuation.
    – jimchristie
    Dec 22, 2014 at 14:02

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.