I mash a lot and wind up killing chainrings. I later find that my chainring warps at the midpoint between two chainring bolts. Usually my first sign that something is wrong is my chain pops off or breaks and I can see the bump in the chainring that caused it.

I've gone through a 3 or 4 34t/36t chainrings between my single speed track bike and geared cross bike bike with a shimano deore drivetrain. Both have bash guards protecting the outer ring, so I doubt impact is a factor.

When replacing these, what is going to resist bending more, steel or aluminium?

  • Unless you're a real gorilla, I doubt that you can bend a ring without either impacting it or getting the chain crossed. As to which is stronger, a properly tempered steel ring would be stronger, but most steel rings are cheap stampings. Feb 28, 2013 at 16:08
  • 1
    Bike polo with a 34/20 gear ratio, high torque / low speed and full on sprints. I've seen chainrings bent a few times by other people as well with a similar setup. I've had it happen when I just start pedaling from a dead stop and feel something weird at one point in the rotation and look down to see the bent ring.
    – Benzo
    Feb 28, 2013 at 17:04
  • I've bent the outer ring on my cross bike hopping logs, but that's to be expected. Could I have bent the middle ring by having poor choice in gearing? (most likely the big ring in the rear and middle ring in the front).
    – Benzo
    Feb 28, 2013 at 17:05
  • Bike Polo!? Sure looks like fun! I had to look for it on youtube. They seem to use single speeds or even fixed gears. What is your specific setup for bike polo? Does this happen to you only on bike polo or on other disciplines too? do you use the same bike for polo and for other kinds of riding?
    – Jahaziel
    Feb 28, 2013 at 18:20
  • 1
    As for the cross bike, I'm going to just get a new crankset with a set of steel rings, probably Shimano Deore M591, and try my best to avoid bad cross chaining.
    – Benzo
    Mar 1, 2013 at 14:41

2 Answers 2


As far as My experience gets on mountain biking, cheap steel is more resistant than cheap aluminum, with expensive parts the story changes a lot because many different alloys are used by different manufacturers or even the same manufacturer changes the formula among models.

The advantage of steel anyway is that it can be safely unbent as long as the deformation is not too dramatic.

However, in my case, most of the bent chainrings come from hitting objects on rough trails, except one time that it was due to one of the chainring bolts comming off. I have been kind of a masher myself, but I have never bent a chainring due to pedaling force (I have broken a couple cheap freewheels due to this instead). So I think some other factor may be affecting your problem. A couple of them are:

  • Chainline: The pull on the chain should be pretty straight, so even under extreme forces it is unlikely to bend a chainring/cog. However a bad chainline makes the chain pull in a direction that is too unalligned with the chanring's plane. This can be due to a bad combination of components, specially a bottom bracket of the wrong spindle length, or, more commonly, a bad choice of gears. In a mountain bike the innermost chainring should be used with the 3-5 closest-to-hub cogs, the outermost chainring should be used with the 3-5 furtest-from-hub cogs and if there is a middle chainring it shoud be used (you guessed it) with the cogs in the middle of the cassete. Check the chailine of the gearing you are using most by looking at the chain so your line of sight is aligned with the point where thr chain leaves the cog and with the point where it enters the chainring. If the chainline is wrong you should esily note how the chain bends at the entering-the-chainring point.

  • Frame flex: If your frame flexes easily and you are mashing your pedals, both factors add up so when you are applying maximum force, components are most unaligned, causing forces to actuate on parts at wrong angles, thus making them prone to deformation, but the problem is not evident while evaluating the bike onthe workstand.

  • Bad shifting technique: Shifting gears while applying too much force causes all kind of transmission problems, from bent chainring teeth to bent chain links, broken chains, premature wear and even derailleur malfunction/damage. Proper technique, specially for downshifting while masshing pedals up a steep slope is to a) plan prior to shifting, specially shifting before you exhaust your momentum. b) Accelerate a little just before the shift. c) Ease the force on the pedals while at the same time applying the gearshift. During the whole shifting process you should practically just spin the cranks, you rely on innertia to continue in movement and that is what the previous acceleration was for. d) resume normal pedaling once the shift has completed and the transmission is working silently again. (noise is often a sign of bad shifting).

  • Bent parts: There may be something else bent on the bike. Particularily the crank spider or even the whole crankarm. If thats the case, it is making you loose the chainline at least two times per pedal revolution, once towards one side, once towards the other. This has happened to me with cheap, soft aluminum, square taper crankarms: with heavy use, the spindle interface deformed, causing the whole crankset to rotate off axis causing a set of not-so-funny symptoms, including chainsnap and front shifting difficulties. Careful inspection on the workbench wile manually rotating the cranks is advised. If this is the case, it is diagnosable by eye or a simple ruler/metric tape. A bent frame is less likely but not impossible, however, it may be harder to diagnose.

  • 1
    Yeah, in particular I could see a loose crank arm causing the ring to bend. Of course, it would have to be abysmally loose, but people sometimes ride them until they fall off. Feb 28, 2013 at 22:37
  • "The advantage of steel anyway is that it can be safely unbent as long as the deformation is not too dramatic." +1 for that - my brother bent his steel ring 1/2 mile into a ride we planned for weeks and drove 2 hours for. If it was aluminum it probably would have ruined our day.
    – AlexCuse
    Mar 1, 2013 at 0:55
  • Bad chainline would be my first hypothesis. +1 to this thorough answer. Mar 1, 2013 at 13:44

There are lots of quality chain rings out there in both steel and aluminum. There are a couple of questions I have after reading your post.

  1. How often do you change your chain?
  2. How often do you clean and lube your chain?
  3. How much do you spend when replacing the chain ring. If you are that hard on chain rings you might want to go to a high-end chain ring like these:


Also, if you mash that hard, your knees will start complaining. Spinning is way better than mashing. Maybe a lower gear and more RPMs?


  • 1) I change my chain when my wear indicator tool tells me, I don't track miles. 2) I lube it when I remember, or it squeaks, or if it's really dirty, or if I don't remember when I lubed it last. But my cross bike gets super muddy just about every time I ride it, I at least lube that every ride (regardless of whether i got any or all of the mud off). Polo bike gets lubed less frequently, but usually doesn't get exposed to crap weather. 3) Cheap. My polo bike was an alloy sugino 34t ring, bent a steel vuelta 32 ring on the cross check, bent another cheap steel ring on my polo bike.
    – Benzo
    Feb 28, 2013 at 18:58

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.