enter image description hereI've got an old bike with a quill stem, and the headset arrangement has a nut, and a textured lock ring. I presume I should tighten with a combination of a spanner and mole grip. Is a mole grip the right tool for the job?

  • Can we have a photo? There should be 2 places you can get a (thin) spanner on. – alex Apr 28 '13 at 11:16
  • 1
    Loosen the upper nut a turn or so, tighten the knurled nut, tighten the upper nut (while holding the knurled one). – Daniel R Hicks Apr 29 '13 at 1:02
  • (What the heck is a "mole grip"? Slip-joint pliers?) – Daniel R Hicks Apr 29 '13 at 11:39
  • Are you from the states? – Andrew Welch Apr 29 '13 at 12:24
  • Mole grips ~ vice grips (because they sort of look like a mole? I don't know...) – WTHarper Apr 29 '13 at 19:02

Daniel is right. If you tighten the knurled ring by hand, but not quite as hard as it will go, then use a large spanner to tighten the locknut down against it, which will tighten the race slightly more, you won't need any sort of pliers (or, less likely to damage anything, a strap wrench). You might need to back off and try again a few times to get the load right so it turns freely but without play.

| improve this answer | |
  • +1 for strap wrench. I wouldn't like to use anything else for fear of warping the top race. – alex Apr 29 '13 at 23:35
  • I wouldn't expect pliers used with care to do more than mark the knurled surface, and maybe not even that. But they should be a last resort. – armb Apr 30 '13 at 5:56

I believe this style is meant to be tightened by hand.

To tighten, start by tightening the knurled/textured upper race a little harder than you intend it to be once you're done.

Next, add the washer and screw on the locknut as hard as you can without tightening the race any more than it already is. Too tight and you may damage the races and need a new headset.

Then whilst holding the locknut still with a spanner, unscrew the race by hand as hard as you can. The idea is to be it clamped against the locknut so neither can move.

You may need to experiment with how tight you start to get the right tightness at the end.

PS. Mole grips are almost always the wrong tool.

| improve this answer | |

I'll add that anything hand tight will come loose fairly soon. As the knurled race loosens it will start to damage itself an/or the ball bearings and cause sloppy handling and steering. I'm not saying that you want to torque the race down to the fork, but up against the lock nut as @alex suggests:

Then whilst holding the locknut still with a spanner, unscrew the race by hand as hard as you can. The idea is to be it clamped against the locknut so neither can move.

My point is that "by hand as hard as you can" won't be good enough. You will need a tool that can grip the knurled race evenly. A pair of slip-joint adjustable pliers which are the right size will work. You want to be able to get both sides of the pliers parallel with each other when gripping the race. Anything less will potentially slip and cause damage to the knurled surface. You might even be able to get a pair with plastic covers over the teeth to protect whatever you are gripping.

slip-joint adjustable pliers

About mole grips or locking pliers for us in the US (http://en.wikipedia.org/wiki/Locking_pliers) I've never found a pair that were large enough to do this. Also, you lose the hand feedback that regular pliers give you. You won't know when the race is about to slip until its too late.

| improve this answer | |
  • 2
    You tighten the locknut (using a standard wrench) down against the knurled nut. No need for the slip-joint pliers. (And if you feel you MUST use something, use a strap wrench.) – Daniel R Hicks Apr 30 '13 at 1:19
  • 1
    Eventually as you tighten the locknut, the friction between the locknut and the adjustable race will cause the adjustable race to tighten down against the upper head race. You want to avoid this. The goal is to tighten the locknut and the adjustable race against each other. To do so, you'll need to hold both pieces. – tir38 Apr 30 '13 at 19:06
  • + 1 @DanielRHicks for the strap wrench – Andrew Welch Oct 27 '17 at 9:48

I just had some success by using an old innertube to get a MUCH better grip on the "knurled ring"-on my bike this ring is not knurled, it just has a bunch of straight edges but nothing really wrenchable.

| improve this answer | |

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.