217

This question and its answers list the names of bike parts and cycling concepts.

Some Rules

  • Make sure you only put one term per answer!
  • Try to include an image if applicable
  • Include sources that contain detailed information
  • Add a link to the index in this question using edit.

Also, I made this a community wiki, so that anyone will be able to edit it, and to stop rep-hoarding


There's a handy reference at the Park Tool Co. website, a bike repair map; it's a diagram of a bike with all the parts labeled, and is very handy! At the moment, the diagram is up at parktool.com/blog/repair-help. (They've changed the URL in the past, so this link may break.)

A road bike has the following parts (source):

enter image description here

A mountain bike has the following parts (source): enter image description here


Edit: This page is meant to identify what things or concepts are (as per this thread in meta). If you want to recommend an accessory or a specific product you've found handy, please use the accessories page.


Contents
Actuation Ratio
Axle
Axle Nuts
BCD (Bolt Circle Diameter)
Bearing
Belt Drive
Bidon/Bottle
Bonk/Bonking
Bottle Cage / Bottle Holder
Bottom Bracket
Boom/Boom Tube
Brazed Frame
Brifter
BSD (Bead Seat Diameter)
BSO/Bike-Shaped-Object
Cable Pull
Cable Stretcher
Cadence
Cassette
Chain
Chainline
Chain Gauge
Chain Guard/Cover
Chain Tool
Chain Tug/Chain Tensioner
Chainstay Length
Chainsuck
Chamois
Clipless Pedals
Coaster Brake (foot brake / pedal brake)
Crank
Derailleur
Derailer Hanger/Derailleur Ranger
DetanglerBMX
Direct Drive
Disk/Disc Brake
Disc Hub
Door Zone
Dropout
Dropper Post
Dunlop Valve
e
Engine/Motor
Electronic shifting
Eccentric
Fender/Mudguard/Mudflaps
Fixed-Gear
Flip-Flop Hub
Folding Bike
Fork
Foot Peg
Frame
Frame Sizing
Gear Inches
Groupset
Handlebars
Headset
Hose Clamp aka Jubilee Clip
Hub
Hub Skewer
Internally-Geared Hub
j
Keel Tube
Lawyer lips/lawyer tabs
Lateral Tube
LBS/Local Bike Shop
Lights
Luggage Carrier/Rack
Lugged Frame
Master Link
MIPS
Mixte
Mountain Bike
n
Noodle
o
Over Locknut Dimension or OLD
Pannier
Play
Potts Mod BMX Brakes
Power Meter
Presta Valve/Presta Tube
Pump Peg
Q-Factor
Quick-Release
Recumbent Cycles
REI (Recreational Equipment Inc)
Rim
Rim Tape
Rim Brakes, e.g. cantilever, dual pivot, V-brakes
Rotor
Saddle
Saddlebag
Schrader Valve/ Schrader Tube
Shaft Drive
Single-speed
Skewer
Spider
Spoke
Stack and Reach
Stay, Mudguard/fender
Stem
Suspension Fork/Rear Shock
Through/Thru Axle
Tire, Clincher
Tire, Tubeless
Tire, Tubular
Tire, Solid/airless/runflat
Tire Boot
Tire Clearance
Tire Lever/Tire Iron
Tire Saver
Tire Sealant
Tolerances
Track Pump/Floor Pump
Triathalon Bars/Triathlon Bars
u
U-Brake
V-Brake
Velomobile
Welded Frame
x
y
z
10
  • 8
    One term per answer please - would be beneficial.
    – dotjoe
    Aug 26, 2010 at 13:51
  • 1
    Is there a way to link to a specific answer, so that in future questions you can use one of these terms and link to it for reference?
    – Kevin
    Aug 26, 2010 at 16:13
  • 2
    Kevin: Under the bulk of the answer, there is a 'Link' hyperlink, which will link to the answer (its right above comment) Aug 26, 2010 at 17:12
  • 8
    @MarkIngram: useful things that aren't actually questions are what community wikis are for.
    – freiheit
    Sep 12, 2010 at 17:47
  • 2
    This page could use some more love. Maybe if people keep linking to individual terms here, more people will know about this page. Jun 27, 2011 at 2:39

99 Answers 99

11

Frame or frameset

The frame is the skeleton of a bicycle. It's the part that all other parts are attached to. (Some parts, like the front wheel, are attached to other parts that are in turn attached to the frame.) A frame plus a fork are often called a frameset. The frameset's geometry determines the bike's handling characteristics.

Frames are usually made of steel, aluminum, carbon fiber, or titanium. Less common frame materials include bamboo, other types of wood, or magnesium alloy.

Aluminum mountain bicycle frame:

100_7864

Parts of a bicycle frame:

enter image description here

(Image from wikipedia; credit and legalese)

11

Rack, aka Luggage Carrier

A rack is a frame attached to a bicycle to provide space for a pannier or other type of pack to be attached. Not all frames and forks are built with rack mounts. Racks can be mounted at the rear of a bicycle, for example on the touring bike below: enter image description here

Or front racks mount to the fork, as shown in a photo from Cyclingabout.com:

enter image description here

Reference:

11

Disc Hub

Disc hubs are designed to mount disc rotors. Rotor mounts come in two varieties: 6-bolt ISO and Shimano's proprietary Centerlock spline. Converters exist to allow a Centerlock hub to accept a six-bolt disc rotor.

6-bolt ISO:

ISO disc hub

Shimano Centerlock: (Note, centerlock hubs ship with a rubber cover over the centerlock splines). Centerlock disc hub

You cannot mount a disc rotor on a non-disc hub. You can use a 6-bolt rotor with a groupset that is otherwise designed for centerlock rotors or vice versa.

1
  • Most Rohloff hubs are also "disk hubs", and come with a proprietary 4 hole mount. No adapter is possible, the reason they do this is because they need a bigger hole than the other mounts allow.
    – Móż
    Jan 14, 2017 at 6:09
11

Chainstay Length

The chainstay length is measured from the center of the front chainring (centered on the bottom bracket spindle) to the center of the rear cog (centered on the rear axle). Longer chainstays stabilize the bike's handling. Touring and many gravel bikes have longer chainstays, whereas many racing bikes, especially on the track, have short ones.

The chainstay length is typically measured directly from point to point but might be measured horizontally (parallel to the ground) which will give a slightly shorter value. If possible, check the geometry chart to see how it is defined. Frames with horizontal or adjustable dropouts have variable chainstay length, unlike frames with vertical dropouts. In the former case, the manufacturer may state the chainstay length as measured to the middle of the adjustment range.

Chainstay Length

There are formulae for calculating chain length, based on chainstay length and cog sizes, which are used in online chain length calculator.

0
11

Hub

One of the central parts of a conventional bicycle wheel. Hubs are flanged metal tubes, somewhat similar in shape to spools of thread. Hubs contains bearings and an axle, and they are connected to the rims via spokes. The rear hub holds the freewheel or cassette.

Maintenance

The bearings in your hubs are wear items. This is discussed more in the bearing article, but cup and cone hubs require annual service. The cones may eventually wear out and can be replaced. Cartridge bearings usually do not require service, but they will eventually wear out. A competent bike store or a consumer with the right tools can pull them and replace them. The freehub body can often be obtained from the hub manufacturer as a replacement if it wears out. If the hub is OEM equipment on a complete bicycle, the bike store should be able to search for replacements in their inventory.

Good hubs can outlast a rim. Currently, many consumers buy complete wheels, but you can also buy separate hubs and ask someone to build you a wheel, or have a hub from a damaged wheel taken out and reused. If you damage or wear out a rim, consider if rebuilding on the same hub is more cost-effective than buying a whole new wheel.

For consumers, some key features are:

  1. Spacing and axle type

If you are getting a new wheel, you will need to make sure that these features match your current bike. Quick release road and MTB hubs had 130 and 135mm over-locknut diameter respectively. On thru axle hubs, road hubs wheels use a consistent spacing and mostly use 12mm diameter thru axles front and rear. MTB hubs likely use 15mm diameter thru axles, but you need to consider if the bike uses Boost spacing (148mm in the rear) or not (142mm, same as disc road bikes).

  1. Drivetrain

You need to match the rear hub's freehub body to your drivetrain. Shimano road hubs have mainly used the Hyperglide system, but the 12s Dura Ace hubs are transitioning to a different spline system (name not yet determined), and they use the Microspline system for MTBs. SRAM has shifted to the XD and XDR driver systems. Campagnolo has maintained its own freehub spline pattern, with an additional variant (called N3W) to accommodate the small cogs on its Ekar gravel groupset. Alternatively, you may have a freewheel hub, and you would thread a freewheel onto the hub.

If you switch drivetrains, replacement freehub bodies are usually available from the hub manufacturer.

  1. Disc or rim brake

Hubs designed for disc brakes will have their flanges spaced so as to accommodate the rotor, and they will have a mounting system. As to the latter, the two rotor mount standards are 6-bolt (mostly used on MTBs) and centerlock (used on drop bar bikes). Rim brake hubs cannot be used in disc brake systems, as there is nowhere to mount the rotor.

  1. Other features
  • Internally geared hubs contain all the gears inside the hub. They don't have freewheels, but they do have an external cog to attach a chain or belt drive. These typically have higher drivetrain friction than (properly maintained) derailleur-based systems, but they are much more resistant to contamination. They may use belt drives or chains for the transmission.
  • Track/fixed-gear hubs may have narrower spacing than other hubs. They will not have a cassette body, and they will accept a thread-on cog on one side of the hub.
  • Flip-flop hubs have a cog is mounted on either side of the wheel. According to legend, Tullio Campagnolo was inspired to develop the quick release skewer when he tried to flip a flip-flop hub secured by wingnuts in cold weather. This may not be strictly true, but Campagnolo was one of the first to put a high-quality quick release skewer into serial production.
  • Both front and rear hubs can accommodate electric motors. Users should be aware that they will change the bike's weight distribution and thus its handling. The batteries are mounted elsewhere on the bike. The crankset is an alternative area for mounting a motor (i.e. a mid drive e-bike).
1
  • What is the actual name of the cylinder on which cassette goes? Wikipedia states "splined shaft", here you use term just "splines". Mar 26, 2019 at 18:31
11

Brifter

A combined brake and shift lever. May be called integrated shifters. On road bikes, “shifter” may be understood to include the brake lever as well, but this is not true for mountain bikes. The specific term may be more common in the UK than the US. The image below shows a Campagnolo brifter for road bikes.

brifter

Reference:

11

Hub Skewer

A metal rod with a clamping mechanism that attaches the hub/wheel assembly to the fork or frame. Many skewers are equipped with a quick-release mechanism that allow removing the wheel without tools, facilitating changing a tire, putting a bike in the back seat of a car, etc. Unfortunately, the trade-off for easy wheel removal is that it's easier for thieves to remove a quick-release wheel. Skewers without a quick release will use a hex or Torx wrench for removal. It is also possible to secure the wheels with axle nuts, many of which use a crescent wrench of appropriate size.

enter image description here

10

Folding Bike

AKA Folder

A bike that's designed to fold down to a small package without disassembly. They usually have smaller wheels, and are designed to be taken on trains and buses. Many transit organizations that don't allow bikes during peak hours will allow folding bikes during these busy times. They also reduce storage space requirements, often useful in city apartments.

There are also bikes that do not fold, but are designed to be taken apart easily, with frame latches, quick-release latches, or hybrid folding/unlatching systems.

Folding bike, ready to ride

Folding bike, ready to ride

Folding bike, in folded position

Folding bike, in folded position

10

Internally-Geared Hub

A setup where the gearing mechanism is sealed in the rear wheel's hub, away from water, road salt, and other contaminants. Internally-geared hubs require much less in the way of cleaning than traditional drive-trains. These hubs are popular with commuters or other utility cyclists who frequently ride in snow and rain. They are also popular on folding bikes, as they are suited for bikes taken on crowded trains. When coupled with a single front chainring, IGH drivetrains permit the installation of a full chain guard, which most external gear systems don't allow. They can also shift when the bicycle is completely stopped, unlike derailleur drivetrains. Gearboxes are related, and they put the gears in the bottom bracket area.

Internal hubs are slightly heavier than comparable external drive-trains. They also have greater drivetrain friction than a well-maintained external drivetrain.

They will typically require oil to lubricate the gears, which can be injected through a port.

Hub

Reference:

9

Saddlebag

(a.k.a. seat bag, wedge bag, etc.) Small bag designed to be attached to the underside of a bicycle saddle, usually large enough to hold tools to change a flat tire.

The name "saddlebag" is often mistakenly applied to panniers which resemble saddlebags used on motorcycles or horse saddles.

1
  • also known as a wedge-bag/pack
    – mgb
    Oct 22, 2010 at 3:52
9

Master link

Also known as:

  • Quick link
  • Breakable link
  • PowerLink™ (made by SRAM)
  • MissingLink (made by KMC)

A link inserted onto a chain so that the chain can be both assembled and "broken" (disassembled) without a chain tool. A set of pliers or a flathead screwdriver is usually sufficient to disassemble a chain with a master link.

Master link pliers are available to open a master link. Note that not all designs of master link are sold as suitable for re-use.

More information at Sheldon Brown's site.

enter image description here

Image from Wikipedia

9

Crank, aka chainset, crankset

We turn the pedals and cranks with our legs. Pedals screw into threads at the end of the crankarms. The cranks themselves are, in turn, attached to the bottom bracket. Gearing is controlled by the size of the front chainring(s).

Some key concepts:

  • Length: Cranks have traditionally been available in lengths of 170mm, 172.5mm, and 175mm, with many manufacturers now offering shorter or occasionally longer lengths too. Mountain bikers riding long-travel bikes and triathlon cyclists may have started this trend of using shorter cranks.
  • Chainrings: Cranks are usually designed for use with between 1 to 3 chainrings, although 4-ring designs have existed historically. The chainrings control the gearing available to the bicycle. 1x systems with a single front chainring (pronounced "one-by") are common on mountain bikes and gravel bikes. They frequently have teeth specially designed to retain the chain (e.g. narrow-wide chainring). Other technologies such as a clutched rear derailleur and possibly a chain guide aid chain retention also. 2x systems are common on road bikes, and have pins and ramps to guide the chain to the large ring. Triple chainrings were once standard on MTBs. They may be more common on older touring bikes also. Front derailleurs are typically specific to triple or double chainrings.
  • Bolt circle diameter: determines what sizes of chainring can attach to the crankset. Some cranksets use direct mount chainrings instead, which are secured to a splined interface at the crank arm. Different manufacturers have different spline patterns, and bolt patterns may vary too despite the BCD value.
  • Bottom bracket attachment or axle type: Cranksets may be designed to mate to a specific bottom bracket, in the case of square tapered, older Shimano Hollowtech, or ISIS cranksets. Alternatively, cranksets may be designed around a specific axle type. For example, Shimano, SRAM, and Campagnolo use 22.00 to 28.99mm diameter axles. Some third party cranksets have 30mm axles. Bottom brackets are not necessarily inter-compatible despite being designed for the same spindle diameter, so be sure to check with manufacturer guidelines. Note: some “24mm” FSA cranks are actually 24.07mm and will not readily fit standard 24.00mm bottom brackets.
  • Chainline: the distance from the centre of the bottom bracket to the center of the chainrings or chainring. Typically, road double cranksets have a 43.5mm chainline. Non-boost MTB cranksets are around 50mm, but wider chain lines are available for boost and super boost bikes. The advent of disc brakes on road and gravel bikes has led to some cranksets with 45mm chainlines. Front derailleurs are designed for optimal performance on a specific chain line. Mixing a road front derailleur with a 45mm chainline crankset may work, but it may not be optimal. Mixing a road derailleur with a 50mm chainline is very unlikely to work.
  • Maintenance: The cranks themselves don’t typically require maintenance, but the chainrings will wear eventually. Typically, they will outlast the cassette.

Miscellaneous:

  • Cranksets can also connect to motors attached around the bottom bracket (on E-bikes) and/or to gearboxes mounted in the bottom bracket area.
  • Sheldon Brown has more information on cranks.

[Crank arms](https://flic.kr/p/nyQzv4)

9

Rim

The circular, U-shaped (in cross-section) part of a bicycle wheel that the tire and spokes are attached to. Rims attach to the hubs with spokes. Wheel-building is the process of attaching a hub to a rim with spokes, including bringing the spokes up to tension.

With rim brakes, the rim's braking surface will eventually wear out. The metal will become dangerously thin, and it may crack, as this image from Sheldon Brown's site shows. Some rims have a dimple in the sidewall as a wear indicator. When the wear indicator is no longer visible, replace the rim. Otherwise, check for concavity by holding a ruler to the rim. The photograph below was originally posted to the Bike Radar forum and it depicts a rim due for replacement. Wear due to braking is not an issue with disc brakes, as that is borne by the disc rotors.

enter image description here

This image shows a worn rim that has cracked.

enter image description here

Maintenance

  • If you ride in the wet with rim brakes, it is good to clean off your rims and brake pads afterward, as the grit from the road will abrade your rims.
  • Rims can come out of true, i.e. they will wobble side to side or up and down (the latter is sometimes called being out of round). They can be trued by adjusting the spoke nipples. Tightening a nipple increases the spoke's tension, which pulls the affected rim segment in the direction of the spoke. Wheels, especially mass produced ones, do not always come true from the factory. Most cyclists get a bike store to do this, but you can true your wheels at home with a spoke wrench and, preferably, a truing stand. You can use the frame and/or your brake pads as a makeshift stand, but commercial ones are available.
  • If an aluminum rim gets bent in a crash, it can often be straightened. This is less necessary on disc brake wheels that are not being set up tubeless.
  • If you must replace a rim due to a crash, consider if reusing the hub is more economical than buying a new wheel. If the damaged wheel does not use proprietary spokes or rim drilling patterns, you are not limited to replacement rims from the original manufacturer. Make sure to match the number of holes in the old rim to the new one. Old spokes are generally not reused, and a different rim will require different length spokes anyway. A bike store can help you determine the spoke lengths that are needed. Some examples of major rim manufacturers with a wide range of price points are DT Swiss, Velocity, and Kinlin, although there are numerous others.

Characteristics

Buyers comparing rims or complete wheels (often called wheelsets) may be interested in the following characteristics.

  • Size: Rims are often given a nominal size. The formal way to measure size is the diameter at the bead seats, in millimeters. 700c road bike wheels and 29" MTB wheels share the same BSD of 622mm. These are the most common wheel sizes in these disciplines. The Bead Seat Diameter article, linked earlier, has more discussion.

  • Internal width: this is the width measured between the bead hooks if present, or the inner faces of the sidewall if the rim is hookless. All else equal, the same tire will be wider on a rim with wider internal width. Internal widths have grown much wider over time for both road and mountain bikes. External width is sometimes listed, but it is arguably less important unless you’re trying to maximize aerodynamics (here, you ideally want your tires to measure narrower than the external width).

  • Tire types and hooked or hookless: Tubeless-compatible rims can fit tubed or tubeless clincher tires. You can run a tubeless clincher with a tube inside. Older clincher rims may not accept tubeless tires, so check that a rim explicitly indicates tubeless compatibility if this is important. More rarely, rims can fit tubular tires, which are glued to the rim bed. At the time of writing, many MTB wheels and newer road wheels, especially carbon ones, are hookless, meaning that they don’t have bead hooks. Not all clincher tires are compatible with hookless rims, so make sure your tire explicitly states this. Hookless rims are easier and cheaper to construct in carbon. Tubular tires do not fit on clincher rims, and vice versa. Tubulars are extensively used in professional road racing, and they are typically safer to run if punctured than clinchers, but you have to be able to prepare and glue the tires (or pay someone to do so).

  • Holes: Relevant if replacing a rim or having a wheel built. Fewer spokes means slightly more aerodynamic wheels, although the differences are small. Rims and wheels for performance road bikes may be available in 20, 24, 28, or 32 spokes, with 20 spokes typically only being available for front rim brake wheels. Rims for tandem road bikes tend to have more spokes.

  • Tire widths: You can mostly mount whatever width of tire you want on the rim. This discussion has more information on what width of tires are compatible with rims. However, the frame's tire clearance is more likely to be the limiting factor than the rim. Some aerodynamic wheels will specify what tire widths are optimal to maximize aerodynamics. Some rims may explicitly state a minimum width. Check the manufacturer website for details.

  • Aluminum rims are extruded as a bar, then rolled into a rim. The ends of the bar are pinned together, held together by a sleeve, or welded. Pinned rims are generally the cheapest. Carbon rims are made in one piece in a mold. They can be made lighter than aluminum rims of the same depth. A deep, aerodynamic aluminum rim would be very heavy. Carbon rims for rim brakes generally have poorer braking than aluminum rims, although rims and brake pads have improved.

Clincher rims require tape on the rim bed to cover the holes that are used to insert spoke nipples. A few clincher rims may not have these holes, and the manufacturer will explicitly say if this is the case.

8

Lawyer Lips/ Lawyer Tabs

Bicycle forks with quick-release wheel mechanisms are often equipped with these. The intent is to make it less likely that the wheel will accidentally release if the quick-release lever is used improperly.

lawyer lips (thanks to sk606 for the image)

In practice, they make it difficult to use the quick-release without unscrewing the skewer, making the quick-release harder to use. It is thought that these were added to bikes after a lawsuit, which explains the name's origin. Professional cyclists would frequently file these off, as they may need to change wheels quickly during a race.

Disc brakes impose asymmetric torque on the hub, and they may cause skewers to be ejected from dropouts. Lawyer lips help prevent this. However, bikes with disc brakes now overwhelmingly use thru-axles, which physically can't be ejected by torque.

8

Spider (part of the crankset)

The part that connects the crank arms to the chain rings. You bolt the chainrings to the spider. In the past, you merely needed to find chainrings appropriate to your transmission (e.g. 8 speed, 9 speed) whose bolt circle diameter matched the spider. Many end 11 and 12 speed cranksets have moved to 4-arm asymmetric designs, so you will need OEM replacements or chainrings that are designed to mate with the specific crankset.

Historically, most spiders have had 5 legs, and the crank arms and the spider were forged or molded (for carbon cranks) as one piece. With some cranks, the spider may be constructed separately, or the crankset may use chainrings that incorporate a spider. In either case, the spider or chainring would mount to a splined interface at the base of the crankarm.

Image from trekstorecolumbus.com

Some cranks use direct mount chainrings. Here, the spider is a part of the chainring, and the crankarms have a splined interface. This is discussed more on the article on cranks.

2
  • 2
    Note: the study of spiders is Arachnology :-)
    – andy256
    Jul 15, 2015 at 2:27
  • Two suggestions: make the entry logically consistent, and add the apparently missing words. If my name is to be attached to such bosh then it looks like it's time to delete my account.
    – andy256
    Nov 12, 2021 at 2:34
8

Spoke

The spokes connect the hub of a wheel to its rim. Spokes are secured to the rim by a spoke nipple. They insert into the hub at its flanges. Spoke count is the number of spokes in a wheel, and a higher spoke count usually means a stronger wheel that can handle more weight and abuse.

Spoke tension (the force with which the spokes are tightened) can be adjusted individually. This is part of the process of truing a wheel, ensuring the rim does not wobble side to side or up and down. This is particularly important with bikes that have low tire clearance, but wheels that are trued are a benefit to any bike.

Almost all spokes are made of steel. In performance bikes, spokes are sometimes bladed or ovalized, which reduces the wheel's air resistance slightly.

7

Chamois

The padding in a pair of cycling shorts. Traditionally this was made using chamois leather but is now usually a synthetic material.

Chamois cream can be used to prevent chafing while riding. With chamois leather, it can dry out and stiffen, so chamois cream is applied to the chamois to keep it supple. Modern chamois creams, however, are designed to be applied to the rider themselves rather than the synthetic padding.

1
  • 6
    And chamois cream is better known as "butt butter". Jul 31, 2011 at 18:24
7

Mountain Bike

Often abbreviated as MTB. A bike with sturdier wheels (usually 29" or 27.5") and wider tires - at least 2" wide - meant for riding off-road. They are also characterized by flat handlebars, which offer better control in very rough terrain than drop bars, and they almost always have suspension. Modern MTBs also have very different frame geometry than road bikes, tending towards relatively upright positions.

Mountain bikes commonly come with front suspension (hard tail) or both front and rear suspension (full suspension). (Rigid) MTBs without any suspension do exist, and they require much more careful choice of lines. In the past, soft tail MTBs had a small, low-travel suspension where the seatstays joined the frame.

1
  • Any MTB riders able to improve this or the suspension article? I am unfamiliar with MTB subtypes, but they could be helpful to list. On suspension, I tried to list key concepts but am not certain if all were described correctly.
    – Weiwen Ng
    Dec 3, 2021 at 23:56
7

Mixte, Step-Through Frame

A mixte is a frame with 3 sets of stays instead of the usual two. Riders don't have to raise their legs far to get them over the top tube. These frames were an advantage to women wearing dresses. The image below is courtesy of Sheldon Brown's site.

enter image description here

The middle set of stays usually runs all the way to the head tube replacing the top tube, but on some mixte frames, the top tube is still a normal single tube. The traditional mixte has those axle-to-head stays straight, but there are also designs where they're bent to give an even lower standover height. They still retain the usual chain stays and seat stays. This design keeps the frame strong and doesn't require a longer seat post.

Wikipedia notes that the word mixte may come from the French word for mixed (as in mix of women's and men's styles) or unisex.

1
7

Welded Frame

A frame made by melting the tubes it is built from at the joins, typically with a similar metal added as filler. For steel bikes, welding is more amenable to mass production than brazing or lugs. Aluminum and titanium bikes have typically not used either of the other methods, although some frames have carbon tubes bonded to metal lugs. Welding is typically done under an inert gas. Framebuilders must prevent contamination at the welds from oxygen or other materials. If this is not done, the weld can fail later on.

welded frame joints

0
7

Pump Peg

A pump peg is a small protrusion on a bike frame which is intended to facilitate the mounting of a "frame pump". Depending on the style of the frame, the peg may be positioned to allow the pump to fit on the underside of the top tube (of a standard diamond frame) or on the trailing side of the down tube. The peg is designed to mate with a corresponding hole in the end of the pump. The pump is spring loaded, and the expansion of the spring holds the pump in place.

Some schemes have a peg at each end, while others reply on the other end of the pump being wedged into the V formed by the top tube and seat tube.

enter image description here

enter image description here

7

Cage/Bottle Cage/Bottle Holder

Water bottle cages hold water bottles on a bike frame. Most cages attach to the frame via preinstalled threaded holes that are usually called bosses or mounts.

Most modern frames have at least two bottle cage mounts, one on the seat tube and one on the down tube. Some bikes, especially gravel bikes, have a third mount on the underside of the down tube. However, full suspension mountain bikes may have only one mount, as the suspension system can take up some room in the bike's main triangle.

On frames without mounts, bottle cage adapters might be able to strap around the tube. Alternatively, you may be able to drill a hole into the frame and put in a threaded insert called a riv nut. On metal frames with thicker tubing, this is likely to be safe, but it does create a stress riser which may later fail, and it will void any warranty.

A couple examples of cages are shown:

Carbon Fibre Aluminum

For time trials and triathlons, there are also cage adapters that attach to the seat and provide mounting points for extra water bottle cages and spare tubes/inflators. A few new mounts place a water bottle between the extension of an aerobar set. (Image credit to Slowtwitch.com, a triathlon forum.)

Behind the seat Between the extensions

Hydration vests like those made by Camelbak are an option for bikes without any cage mounts or to carry additional water. These may be less comfortable in hot weather. Hydration bladders can also be carried in frame packs that are strapped to the top tube; these packs frequently have exit ports for the hoses. Last, stem bags will strap to the stem and handlebar, and these can carry a bottle also.

Some bikes, mainly gravel bikes, may have mounts on the outsides of the fork blades. These multipurpose mounts can fit standard bottle cages or larger cargo cages. Some gravel and triathlon bikes may have a pair of bosses on the top tube near the stem. These may have the spacing typical of water bottle cages, but they are used for bolt-on boxes (aka Bento boxes) that hold snacks and equipment.

1
6

Hose Clamp

A.K.A. Jubilee Clip

A ratcheting clamp often used to attach items to a bicycle fork or handlebars.

Flashlight attached to flat handlebars with a series of hose clamps.

Flashlight attached to handlebars with a series of hose clamps.

Jubilee Clip on Wikipedia

3
  • 1
    I see how the clamp goes around the torch, but how does it attach to the bars? Is there a second clamp, or does it twist around?
    – Hugo
    Jun 20, 2011 at 8:59
  • 1
    There's a second clamp. Jun 20, 2011 at 14:14
  • 9
    Hose clamps can cut into paint an even metal if they're tight enough. You can stick a strip of old inner tube under the clamp to prevent this (and to provide better grip).
    – naught101
    May 12, 2012 at 3:03
6

Cable Pull

Many brakes and most derailleurs are actuated by pulling cables. Cable pull is how far the cable moves when the brake lever is pulled, or a shift lever is actuated.

For brakes, there are two main standards, short or conventional pull and long or V brake pull. Road bikes have tended to use short pull levers, although current Shimano road brakes operate on a slightly different cable pull than other brands. For mountain bikes, cable-actuated brakes have tended to use long pull. This means that mountain bike V-brakes will not work correctly with road levers and vice versa, although cable pull adapters may be available.

For indexed gears each groupset manufacturer will specify its own cable pull per shift (i.e. each click at the shifter), as well as how far the derailleur travels laterally per shift (i.e. the shift ratio or actuation ratio). Thus, shifters and derailleurs cannot generally be mixed across component manufacturers. Non-indexed (friction) shifters can generally be mixed, provided they have enough total cable pull.

cable pull diagram

1
  • Sorry about the edit war. Short pull brakes are not Shimano specific, friction shifters work if there's enough cable pull.
    – Móż
    Nov 5, 2019 at 4:14
6

Bonk

An expression used by cyclists to describe sudden fatigue or loss of energy while exercising. Also known as crashing, blowing up, or running out of steam/gas/fuel, or empty tank. The phenomenon applies to all endurance sports. In running, it may be called hitting the wall. Bonking is distinct from merely being tired due to lack of sleep or from a higher than normal training load. Subjectively, it can be quite unpleasant to bonk! There can be cognitive effects as well as physical ones.

Athletes bonk when they deplete their muscle glycogen stores. Glycogen is a form of glucose (a simple carbohydrate) that our bodies use as fuel. It is stored in the muscles and liver. This can be reversed by eating immediately, preferably foods high in easily-digestible sugars. Water alone will not reverse a bonk. Bonking can be prevented entirely by eating regularly during a race or training, although this is generally not a concern in sessions under 2 hours. Carbohydrate loading before an event may also make bonking less likely. During an event, you can consume carbohydrates in sports drinks, in pre-made energy chews, gels, or bars, or via real food.

1
  • You've edited out the point that this is an unpleasant result; an experience to be avoided wherever possible. Its more than simply being tired.
    – Criggie
    Oct 21, 2019 at 18:38
6

Brazed Frame

see also lugged frame and welded frame

A method of joining frame parts together by melting brass into the joins between frame tubes. Frames can be fillet brazed or use lugs, which are extra, normally cast metal, parts that the frame tubes slot into before brazing. Lugs make building a strong frame easier, provided you have exactly the right lug for the situation. Fillet brazing offers more freedom but also more skill is required to produce a strong joint. Some people think that there is an aesthetic benefit over welding, as brazing, like some welding techniques, do not leave a rough bead of material at the joints.

Shown is part of a fillet brazed steel frame, with the grey steel contrasting with the copper-coloured brass.

fillet brazed frame

The most common alternative method is welding, where the parent metal is melted and the same or a very similar metal is added as filler. Welding is generally stronger, faster and can be automated but brazing or soldering are sometimes preferred for DIY or aesthetic reasons.

6

Dropout

In the context of bicycles dropouts are a kind of fork end, where the wheels are attached. Dropouts are employed on most bikes; on some mountain bikes the axles pass through holes at the end of the forks.

We often use dropout for any slot to hold the axle at the end of forks, but strictly speaking, a dropout is a fork end where the wheel can be removed from the frame without taking the chain off first. It's called a dropout because after loosening the quick release or nuts the wheel will drop out when the bike is lifted off the ground. It is much quicker and easier to remove wheels with the bike the right way up than when the bike is upside down.

All front dropouts are vertical, and are also accompanied by lawyer tabs to mitigate the risk of improperly closing the quick release skewer. Most rear dropouts are as vertical. However, older bikes often have horizontal dropouts. The image below shows a Colnago horizontal dropout in a Surly frame; a typical example. It has adjustment screws and an integral derailleur hanger. Colnago horizontal dropout in a Surly frame

This image (CC BY-SA) from Wikipedia shows a fork end that is not a dropout. The wheel cannot be removed without removing the chain.

fork end

0
6

Power Meter

Power meters measure your power output. This StackExchange question has more in depth discussion about how to use one, but briefly, they enable structured training (where you do repeated efforts at various intensity levels). They aid in pacing an effort. They are ubiquitous in professional road racing at the time of writing. Very few amateur cyclists need one to progress satisfactorily, as it is possible to do un- or informally-structured training or to train with heart rate. However, power meters can benefit many riders. Power is better than heart rate for pacing an effort because heart rate will take several seconds to respond when you start an interval, and it will likewise take several seconds to come down when you stop an interval.

For structured training, riders estimate their functional threshold power (FTP). This is the maximum power you can sustain for 45-60 minutes, when your body is relying mainly on aerobic (as opposed to anaerobic) processes to generate energy. You can then base intervals off your FTP, e.g. warm up, ride 15 minutes at 93-100% of FTP, recover, repeat once, cool down. Riders typically re-estimate their FTP several times during the season. There are several protocols to do this. A common one is to warm up, then ride a 20 minute maximum effort, then take 95% of the average power during this effort.

A brief history and basic technical information

Power meters use strain gauges, which measure the amount of deflection in a bike component, as well as a cadence sensor. This answer has more detailed information on how power meters work physically. They transmit this information wirelessly to a computer, typically over Bluetooth or a sport-specific protocol called ANT+. The data files can be analyzed by a coach and uploaded to a training site like Strava. Note that power meters require a computer capable of communicating via ANT+ or Bluetooth to work, which is an additional expense. The PowerTap shown below had a proprietary computer, but all current power meters work with most bike computers that have ANT+ or Bluetooth capability.

The first power meters were made by SRM (Schoberer Rad Metrik, a German company), and they were very expensive. As with many electronic goods, they have declined substantially in price in recent years. SRM power meters replaced the chainring spider, and several other power meters are still mounted here. Later power meters were mounted in hubs (e.g. PowerTap, now owned by SRAM, pictured below), one or both crankarms (i.e. without replacing the spider entirely, Stages was probably the first), or the pedal spindles. Less commonly, companies have mounted power meters in the crank spindle. E-bikes also measure power to determine how much assistance to provide.

Image of power meter

Power meters mounted at the crank spider or in the hub will measure a rider's total power, but they do not directly measure the amount produced by each leg (although they can estimate it). Power meters mounted on the crankarms or pedal spindles are capable of actual dual-sided measurement, although note that people may conflate the phrase dual-sided with total power measurement. Manufacturers commonly offer left-only power meters as an entry-level option. Left-only meters measure power at the left leg and double it. This is presumably the weaker leg for most riders, and hence it produces a conservative measure of power. The advantage to true dual-sided power is that you can determine if you have a muscular imbalance, but it isn't clear how critical this is. Additionally, if you have one bike with a left-only meter and you have a total power measurement on another bike, your power measurements may not be comparable, which has implications for FTP testing and effort pacing. Many power meters' software allow you to set an offset, i.e. increase the reported power by x%, which can be one workaround.

Power is key to virtual cycling environments like Zwift, where you simulate a rider's progress through a course and interactions between multiple riders. Virtual cycling programs can accept readings from a power meter. A traditional trainer can be used to estimate power as well, although this is less accurate than an actual power meter. Last, smart trainers measure power at the trainer's flywheel, and they can vary the flywheel resistance to simulate changes in gradient on the course.

Maintenance

Power meters are sealed units. They don’t suffer wear in the same way that chains, cables, and other bike components do. The batteries will need to be replaced periodically, or if the power meter has integrated lithium ion batteries, these will slowly lose capacity. The strain gauges are delicate, and users should take as much care as possible not to knock the power meter unnecessarily.

Power meters may need to be periodically zeroed, I.e. have the software confirm the strain gauge reading when unloaded, like you would tare a weighing scale. Many newer ones can auto zero. If you suspect a power meter is still reading wrongly, another step may be to calibrate the slope, I.e. the change in resistance with a known weight. This is usually done at the manufacturer, although some power meters enable users to do this.

Reference: Wikipedia

1
  • @DanK I was thinking that SRM was a German company, and some wires got crossed in my head, and I made the rather amusing typo about Metrigear being a country that you caught. Thanks!
    – Weiwen Ng
    Sep 27, 2019 at 14:04
6

Dropper Posts

Dropper posts are more commonly found on mountain bikes and on some gravel bikes. They allow the rider to quickly lower their saddle height, and thus their center of gravity. This is useful for very steep descents, where you might otherwise feel like you are going over the handlebars. You actuate the dropper using either a remote lever mounted on the bars or an actuator under the saddle (entry level models).

Cable-operated and hydraulic-operated designs exist. The cable or hose can be routed either internally or externally to the frame (as the frame allows). For mountain bikes, a small release lever is fitted to the handleba. For gravel bikes, the left brifter can be used for the the dropper post (1x transmissions only). SRAM's AXS system can actuate a dropper post wirelessly, usually from the the left shift paddle.

dropper post
(source: evanscycles.com)

4
  • 1
    Maybe we don't need to list manufacturers in these wikis, we can't list them all and makes can go obsolete, we want the entries to be as enduring as possible
    – Swifty
    Sep 25, 2019 at 10:31
  • Excellent! Want to add an entry for "seatpost" too? We don't have one listed. Could be worth adding why a MTB rider might want to lower their saddle, without stopping.
    – Criggie
    Sep 25, 2019 at 10:32
  • I concur with Swifty, and I’ve deleted the manufacturer list. If others disagree, I can revert. I changed the entry on power meters to delete the list of manufacturers I added, but for historical interest i mentioned SRM, the first company to make a commercial power meter. If there’s interest in that sort of history here, I would vote for adding that.
    – Weiwen Ng
    Nov 16, 2021 at 16:38
  • Imagine rocking up two years late for an edit :D
    – Lucero79
    Nov 19, 2021 at 13:21
5

Chain guard/Chain cover

It's a frame, usually made of plastic or metal, that covers the entire length of the chain or only the upper part, mainly for protecting the rider from the dirt and lubricant on the chain, but can also protect the chain itself.

http://commons.wikimedia.org/wiki/File:Bike_chain_guard_full.JPG

http://upload.wikimedia.org/wikipedia/commons/thumb/6/69/Bike_chain_guard_part.JPG/320px-Bike_chain_guard_part.JPG

Not the answer you're looking for? Browse other questions tagged or ask your own question.