I've got a Shimano Deore 3x front derailleur and it works perfectly fine while warm.

But after a ride in cold (about -10..-15 C) there is a problem in shifting up: first time I pull the lever it goes without any tension - like the cable is torn - and nothing happens. The second time it works fine.

Downshifting is ok, and rear derailleur works well too. So: do I need to worry and what is the reason for this?

  • for anyone interested: a bit of wd-40 and muc-off wet lube seem to have solved this issue, but it's a bit warmer now, so can't be sure
    – k102
    Jan 18, 2017 at 7:09

3 Answers 3


There are three places to explore: the shifter, the cable housing or the front derailleur.

Given that you can't shift up (to a higher/bigger front chainring) and that the shifter feels that it's disconnected, my guess is that it's the shifter (#1 below) that is frozen since the symptoms of #2 and #3 are that shifts down to a smaller chainring are slow/harder; and/or that the shifter feels hard/stuck when shifting up, not loose which is what you're experiencing.

  1. If you have an indexed thumb shifter, then these are known to have lubrication problems and will eventually freeze up in the way that you mention (shifting up doesn't work, it feels like the cable is disconnected). The simple fix for this is to shoot some WD-40 or other light lubricant into the thumb shifter body and to work it in while shifting up and down. If you can, taking off the top of the housing will work better. This is only a partial fix as eventually the lubricant will stiffen again. You can then do an overhaul of the shifter, or just get a new one from your local bike shop. There are numerous intertubes videos on how to do this, just youtube "[name of shifter] DIY fix"

  2. The simple fix for housing freeze is to try to use an injection of WD-40 (water-displacing formula #40) into the cable housing to expel all of the water and leave a thin film of very light lubricant. I would try to do this when it is warm (or your bike is inside the house) to give yourself the maximum chance of expelling the water. They sell cable lubrication widgets to put on your WD-40 straw, but I find it's sufficient to take the housing nipple off, aim the straw at the raw cable, spray, and then work the shift lever in and out -- keep repeating until you're either tired or there's some lubricant coming out the other end of the cable. This is very messy. Do not wear your favorite shirt and lay down newspaper or cardboard over your spouse's favorite rug before doing this.

  3. If that doesn't work, then I would unhook your front derailleur from the shifting cable and leave it overnight to "freeze." In the morning, I would dry shift the cable and see if it is moving properly. I would also pull and push on the front derailleur shifting mechanism to see if that is also moving correctly. This is step #3 since steps #1 and #2 doesn't require unhooking, hooking up, and readjusting your front derailleur.

    a. If it is the cable that is stiff, I'd replace it since the WD-40 in the first step didn't work. Replacing derailleur cable is relatively easy, the hardest bit is measuring the housing and cutting it to the exact length without leaving burrs. Your bike shop can do this for you.

    b. If it is the derailleur that seems 'frozen' then it requires a good cleaning and lubrication. There's numerous instructionals on the intertubes on how to do this.

  • If a gear or brake cable isn't sliding smoothly and easily, I tend to just replace it outright. A cheap kit is about $5 for both front and rear and contains inner and outer, and misc ferules etc.
    – Criggie
    Dec 13, 2016 at 2:11
  • 1
    True that, but it involves readjusting the FD and dismantling the shifter, which may be beyond a rank newbie's capabilities. So it's easier to recommend to lubricate the cables first - which isolates the problem - and then move onto more difficult matters second.
    – RoboKaren
    Dec 13, 2016 at 2:12
  • @Criggie I think it's not the case since everything works fine in normal conditions. So, yes, will try to lube it first
    – k102
    Dec 13, 2016 at 14:54

My first thought is that the cable (1) isn't connected tightly enough to either the derailleur or the shifter, or (2) the cable needs to be replaced. So, I would tighten the cable WHEN COLD and if that fails consider a new cable.

The cold weather obviously will impact the entire system a little bit due to a small amount of contraction, and this might have a larger effect if the parts/components are old.

A similar discussion is here: http://forum.cyclinguk.org/viewtopic.php?t=19194


Chances are there is moisture in the gear cable housing which has frozen.

  • 2
    Can you expand on this? How to identify if this is the root cause, how to cure, how to prevent future recurrence ?
    – Criggie
    Dec 12, 2016 at 19:09
  • 1
    You know I'm going to say "urinate" on the derailleur cables - don't you?
    – OraNob
    Dec 13, 2016 at 8:34

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.