I recently bought a second hand bike. It rides pretty well, the only nuisance I have is that the previous owner has spread some lubricant on the seat post. I am pretty sure of this because I see on the tube a greasy black material which goes all the way to where the tube goes into the frame.

So now when I ride it the saddle gets lower and lower, no matter how I tighten it (at a rate of about 2 cm/100 km).

So far I have tried to clean the post and inside if the seat tube with a paper towel, which became black as I expected.

This is a picture of the part after the cleaning

seat post

as you can see it there is already a spacer, and there is no quick release.

What is the best way to remove this lubricant?

  • I am suspicious that the post is undersized or the clamp is defective somehow. I'm also suspicious that the components involved are not steel. If aluminum or carbon is involved then you need to figure out what's what before you go much further. Commented Mar 9, 2018 at 22:53
  • What is the frame material? Carbon / steel / aluminium / other? What is the seatpost material? Carbon / steel / aluminium / other?
    – Criggie
    Commented Mar 10, 2018 at 1:33
  • Word of advise, don't exert excessive force on the seatpost clamp. I've had to learn to fit thread-replacement helicoils because of overtightening and stripping an irreplaceable seat clamp.
    – Criggie
    Commented Mar 10, 2018 at 1:34
  • @Criggie, added picture.
    – L.Dutch
    Commented Mar 10, 2018 at 8:19
  • 1
    Is the clamp alloy too? It might have stretched and is not exerting as much force as it used to. Try a different clamp if you can.
    – Criggie
    Commented Mar 10, 2018 at 9:16

6 Answers 6


This is an XY problem. Seatposts should be lubed. While removing all lube may solve your slipping problem, it will likely do so by making the seatpost corrode into place, which isn't something you want.

Instead, fix or replace your seatpost clamp, and/or make sure your seatpost isn't undersized.

  • I agree. If it still slips even with a proper seatpost and clamp a carbon assembly gel instead of grease could help.
    – Michael
    Commented Mar 10, 2018 at 17:20

A thorough way to do it would be to:

  • Remove the cranks, bottom bracket and seat post.
  • Make sure there is a decent hole between the seat tube and bottom bracket shell (might depend on the frame).
  • Ram rags down the seat tube with a broom handle and extract them via the bottom bracket shell.
  • Once the bulk of the grease is removed (or pushed to the bottom of the seat tube) soak a rag in degreaser (WD40, white spirit, citrus degreaser etc) and ram it through to remove the last traces.

This would be a bit of a pain though and you might not have the tools or knowledge to remove and refit a BB.

You could instead try tying a strong cord to the rag so that you can ram it down the seat tube then pull it back out. If the cord breaks or slips though you'll be back to removing the BB or you will just have to leave the rag there.

You should also ask why the seat post is slipping, as they shouldn't do so even when greased. Actually, it is normally recommended that you grease seatposts lightly so that they don't seize in place. Could there be something wrong with the seat clamp? Alternatively, seat posts tend to slip when they are slightly too small for the seat tube. It seems annoyingly common for manufacturers not to spec the seat tube diameter properly but it could be that the previous owner replaced the seat post with one that is too narrow?

If you are dealing with a screw-type seat post clamp (as opposed to a quick release) and you are doing it up as tight as you can in an effort to stop it slipping then I would strongly recommend that you carry a spare one with you. I have broken a seat post clamp doing the same thing and it was quite a miserable cycle with no saddle to the nearest bicycle shop 10 miles away.

If you have a quick release seat post clamp my gut feeling is that you could improve your clamping force by moving to a screw-type one. Get one with a large diameter screw if possible but make sure that screw is made of steel! Some use aluminium for the screw which is garbage. Also preferably get one where the screw threads into a steel insert rather than into the aluminium body of the clamp.

Edit: As the commenters have said, carbon frames should not be greased. They use an anti-slip or 'carbon assembly' paste. This paste might help you even if your frame is not carbon; I've never managed to get a straight answer on whether it works for metal-on-metal contact.

Also the double seat post clamp linked by Carel Looks brilliant. I've not seen such a thing before.

  • 3
    The whole cleaning procedure will depend on the materials of frame and seatpost. If any of the two is carbon, there should be no grease at all. If the frame is aluminium or steel, consider disassembling the bike as much as possible if you have tools and knowledge or have the more difficult bits like bottom bracket removed by your LBS and clean it with solvents for grease. If the bike is carbon the cleaning is best done by a shop.
    – Carel
    Commented Mar 9, 2018 at 16:32
  • 3
    I've had a similar case where a 'double' clamp helped, one where the upper part held the seatpost and the lower goes around the seattube.Like this one: amazon.com/eXotic-Double-34-9mm-31-6mm-Machined/dp/B00N9NB7Y8/…
    – Carel
    Commented Mar 9, 2018 at 16:36
  • 3
    I wouldn't finish with WD40. In the short term it's quite an effective lubricant, and even after that is still oily. The solvent degreasers you suggest are much better ideas (methylated spirits/denatured alcohol can also be effective)
    – Chris H
    Commented Mar 9, 2018 at 17:20
  • 1
    As usual: a picture of the incriminated bit might help. And @Jambo : +1 for the correct diameter of the seatpost. But if the seatpost is carbon it should not be lubricated but coated with anti-slip paste for carbon parts, even if the frame is metal. No grease there.
    – Carel
    Commented Mar 9, 2018 at 18:52
  • @Carel, I'll add a picture tomorrow. Now with the flash the result is hardly useful
    – L.Dutch
    Commented Mar 9, 2018 at 19:11

Hang the bicycle upside down, on a stand if you have one, but you can also simply suspend it with a bit of rope.

Next, you can easily clean the inside of the tube with a bottle cleaner dipped in solvent. Since the bike is upside down, there is no need to remove the cranks and BB.

enter image description here

Gasoline or paint thinner works well to remove grease. The last bit of grease can be removed with something more volatile that doesn't leave a lubricating residue, like brake pad degreaser (or better chain degreaser) for example.

As Carel says: "Use volatile solvents and products outside! Test the effect on paint first. Don't use with carbon parts and keep away from decals and similar."

  • 1
    Use volatile solvents and products outside! Test the effect on paint first. Don't use with carbon parts and keep away from decals and similar.
    – Carel
    Commented Mar 9, 2018 at 18:46
  • Brake cleaner that is bought from a auto parts store is very bad for paint, i would avoid it if you care about the finish around the top of the seat tube, it will also melt plastic if left on.
    – Nate W
    Commented Mar 9, 2018 at 22:41
  • @NateWengert I'm not sure how it's called, I have a spray can of some product I use for degreasing chains, that's what I would use, it's basically short chain hydrocarbons with solvent. I added "chain degreaser" in the answer.
    – bobflux
    Commented Mar 9, 2018 at 22:45
  • Degreaser is good, i just didn't want him to be confused if he indeed had auto brake cleaner so i thought i would specify that.
    – Nate W
    Commented Mar 9, 2018 at 22:51
  • Wear nitrile or other chemical barrier gloves at all times, especially with heavy duty solvents,
    – IconDaemon
    Commented Mar 9, 2018 at 23:04

On one of my bikes, and a previous one, I've had to use a second clamp around the seat post, with an aluminium spacer. Both are cheap steel bikes but even tightening the built in clamp as hard as I dare it doesn't hold. That's with no grease. On yet another cheap steel bike I snapped the clamp bolt trying to do it up hard enough to stop this happening.


The slot in the back can be a focus for water to enter the seat tube and weep its way down into the bottom bracket. Especially if you don't have a rear mudguard/fender.

One common solution is to fit a short section of old tube so it covers the whole clamp and slot area. If you fasten this tube to the seatpost with a ~1.5 inch hose clamp, that can provide enough resistance that the proper seat post clamp does its job.

Downside, its a dirty hack bodge fix, and makes your nice bike look strange.

Having a small amount of anti-seize inside your frame seatpost mount is a good idea, because it stops them seizing in place. Could be yours has grease, where something like copper antiseize paste would be better.


The grease in the seat tube doesn't matter and can help with the post getting stuck later in life. Just clean the imeadiat area where the post and clamp intersect one another. That will stop the creep.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.