I have a single speed bicycle that has some slack in the chain and threatens to come off. How can I reduce this slack?

  • 4
    WARNING. When working on a fixed gear chain. New here, I can't comment on the above, so I thought I'd add this warning. Since there is no slack in a fixed gear chain if you spin the chain and get a finger caught in the sprocket, you can lose a finger. This would be unlikely with single speed instead of fixed gear, but is something you should be aware of if you're going to start adjusting your chain.
    – LanceH
    Feb 21, 2011 at 18:38
  • Spin the wheel backwards and it's the same danger with a singlespeed
    – joelmdev
    Dec 18, 2013 at 14:46

5 Answers 5


If you have horizontal dropouts (the wheel axle slides into the frame from the back of the bike) the dropouts have long slots which will allow you to pull the rear wheel back and take slack from the chain. Be careful to ensure when you torque the wheel nuts down the wheel doesn't slip from being aligned straight, or the chain is running at a slight angle.

If the chain is so stretched to the point where it's falling off, you really should consider replacing the chain. You can get away with removing a link to remove the slack but a worn chain will be prone to sticky links and popping off unannounced.

  • 3
    I'll also add that a tugg nut (eg: surlybikes.com/parts/tuggnut) can make a huge difference. I found that my chain would get loose quickly due to slippage on the dropouts until I got one. It also makes adjusting the tension a breeze.
    – Mac
    Jun 6, 2011 at 5:05

Typically the adjustment would be made at the rear dropouts. Loosen the bolt back there, hold some tension (not a lot) on the rear wheel while you tighten it back.

  • 1
    ... And be sure to align the wheel properly :)
    – jensgram
    Aug 25, 2010 at 20:00
  • @jensgram - good point.. I've found that typically once you tighten down, the wheel will usually stay aligned, but keeping it inline while tightening isn't a bad idea :) Aug 25, 2010 at 20:53

If you don't have a tool to measure chain stretch then a normal ruler can work. The pins on links should line up at the beginning and 12" mark.

I change my chain 2 or three times a year based on the distances I'm riding. Chaning chains regularly means that your gearing doesn't quite wear enough to fit a single chain and it's less likely that you'll have to purchase some new drivetrain components when you get a new chain.

Many/most single speeds also have the rear dropouts set up so you can slide the wheel back a bit. At least last time I looked at them.


The best method I've found for adjusting tension without using a Surly Tuggnut or similar tensioner is to walk the axle back and forth. Generally, just holding the wheel at tension is not enough to get the tension right without undue frustration.

NOTE: while this method works for singles and fixies, it doesn't work with quick releases. (It will also work with eccentric hubs where dropout tensioners don't help.)

The idea is that you install the wheel in the dropouts with the chain routed correctly and then tighten the axle nuts a bit beyond finger-tight. Then, loosen the right axle nut and pull the wheel (using the leverage from the rim) to tension the chain and tighten that nut. You want to get the chain a bit too tight and then gently tap the nut to back off the tension until it is just right. Repeat the process on the left axle nut to get the wheel aligned, keeping one or the other axle nuts tight. Proper tension should allow the bicycle to pedal smoothly without binding and with as little chain droop as possible (the big risk of a droopy chain is that it will derail and that would not be healthy.)

By using the wheel as leverage, you don't need to rely on physically holding the wheel perfectly straight and taught. After you've tensioned and aligned the wheel (the rim should be centered between the stays) be sure the axle nuts are tightened to spec to keep the wheel from slipping forward.

(Additionally, if as you're adjusting your chain tension you find that the tension wobbles - i.e. it is tighter at some spots in the pedal rotation - then you need to center your chain ring!)


Your chain has probably stretched.

An amusing anecdote. I took my 1996 Litespeed Tachyon (20K miles or more on it) into the shop for a tuneup and asked them NOT to change the drive train unless absolutely neccasary, since it would mean changing everything. Its DuraAce so that would be a big chunk of change.

Anyway, turns out my chain had stretched a complete link! It was clearly stretched, but one complete chain link, so he popped out a link and reconnected the chain.

Short of that you will have to decide what you want to do. See if the chain is stretched. They have a tool for this, see if you can borrow one.

  • 2
    If your chain is that stretched it's going to be ruining your cassette and chainrings. I would have thought you'd be a lot better off replacing your chain to save the more expensive components.
    – Mac
    Jun 6, 2011 at 5:03

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.