I've been procrastinating for several years about converting from Presta to Schrader on my Trek 4200 with Bontrager AT650 (erto 559x19) wheels. What finally convinced me was getting three flats on a recent ride. I had only one spare tube and getting a repair shop here in Thailand to deal with the Presta valves was a challenge; even though I had an adapter.

What still concerns me is assertions that doing so will weaken the rim.

I also have a Trek 7.2 FX which uses Bontrager AT750 wheels which have much narrower rims but use Schrader valves.

Does Bontrager do something special with the 750s that enables them to use the larger valve stem hole without weakening the rim?

Or, will I be OK drilling the 650s out to 8.5mm?

  • 5
    Possible duplicate of Schrader tubes in Presta configured Rims?
    – mattnz
    Commented Nov 15, 2019 at 4:20
  • I was going to post there, but the guidelines seemed to indicate that I should ask a new question. So I did. Sorry, my first time posting here.
    – Buadhai
    Commented Nov 15, 2019 at 4:41
  • Its the same question as the suggested dupe, but differs in your exact rim construction. All the answers there apply just as well, so on that basis it is a dupe. Your other option is simply to lay in a supply of presta tubes - a 10 pack would be reasonable, and order more when you get down to your last 3. Or learn to patch tubes yourself - its not hard.
    – Criggie
    Commented Nov 15, 2019 at 9:55
  • 2
    To extend @Criggie's comment, patching tubes is very easy; there are many videos on YouTube that will explain the process. Unless you were very unlucky, three flats on one ride suggests an underlying problem. Either your tyres are very worn, which makes it easier for sharp items to penetrate, or you didn't remove the penetrating item after the first puncture. Commented Nov 15, 2019 at 10:01
  • 1
    Still, no one has an answer to my original question" "...will I be OK drilling the 650s out to 8.5mm?"
    – Buadhai
    Commented Nov 16, 2019 at 21:50

1 Answer 1


Regarding original question: I have personally drilled out approximately 6 wheelsetsto convert them from prestato schrader valves. I have not yet had any of these rims break even though I use them to drive down flights of stairs and such. Mind you I am a lighter rider (approx 80kg), these (aluminum) rims were used on hardtail mountainbikes. Make sure to debur(remove sharp edges from ) the drilled hole properly.

To try and decrease the amount of flats you get you could do a few things:

-make sure the rim tape is in good condition (no tears/holes, make sure it's properly aligned in the rim)

-remove rim tape and check if any spokes protrude more than approx 1-2mm past the top of the spoke nipples, if they do consider shortening these spokes with a file, dremel or the like or adjusting the spokes such that they are no longer protruding (if possible whilst keeping the wheel true/round)

-check rim bed/edges (where the tire contacts the rim) for damage (sharp/pointy spots which could potentially damage the tire), if you find any sand/file them down so they're smooth

-check your tire for pieces of metal/glass/other objects embedded in/under the surface (by rotating the tire whilst removed from the wheel and pinching it every 2cm approx to reveal any splinters, do this on both the inside and outside of the tire

-check if valve hole has any sharp edges

-whilst installing inner tube make sure it is not pinched in between rim and outer tube (inflate inner tube just a bit, check if it is not pinched anywhere and if all is good inflate the rest of the way)

For fixing flats I personally find it useful to clamp the inner tube with patch in between a bench vice (potentially with some pieces of wood in between the vice and the tube/patch for wider inner tubes), you could also use screw clamps for this purpose.

If you're a heavier rider you might want to refrain from drilling the hole larger but as mentioned I have had no issues with it so far and have been using the 'converted' wheels for considerable time now.

  • Thank you very much. I am 77kg. I've almost always been able to identify the source of my flats. And, it's always a puncture. I've not experienced pinched tubes or damage from the rim or spokes.
    – Buadhai
    Commented Nov 19, 2019 at 9:38
  • @Buadhai some of the punctures may be caused by pieces of glass or metal that are still in the tire after patching the hole. So it might be worth checking if this is the case . Sometimes you can't easily see them since they are below the surface but when you ride the bike they get pushed through the inner tube causing a puncture Commented Nov 19, 2019 at 9:40
  • That's certainly possible, but whenever I repair a flat I always remove the tire from the rim and do a visual and tactile inspection to find whatever made the puncture. It's very rare that I can't find the culprit.
    – Buadhai
    Commented Nov 19, 2019 at 21:26

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.