I have a Merida Speeder 300 with a broken spoke on the rear wheel, which is now out of alignment and rubs against the brake pads. Is it okay to true it, at least for a short term solution (and if so how would it be different from normal truing)? Will it cause damage on for the rest of the spokes? Thanks!

Maybe I should mention that I've had this wheel for 4 years (in which I commuted almost daily) and so far I've only had one spoke broken before, which happened a year ago and it was replaced.

  • 3
    Not ideal, but I've done it once or twice as a temporary measure. (But running with a broken spoke, with or without truing, will put additional stress on the remaining spokes.) Commented Dec 11, 2019 at 18:41
  • 1
    Is this a get-home fix for one ride? Or is it a longer term solution for weeks/months? Or something in the middle?
    – Criggie
    Commented Dec 11, 2019 at 18:46
  • 1
    @Criggie Question specifically notes this is "a short term solution."
    – DavidW
    Commented Dec 11, 2019 at 18:59
  • @DavidW fair enough - but short term could still be days or weeks or even months at a stretch. Personally I'd ride home and not again until its fixed, but not everyone has the luxury of a spare bike.
    – Criggie
    Commented Dec 12, 2019 at 6:41
  • On the road yes, otherwise it's just no!
    – Carel
    Commented Dec 12, 2019 at 8:22

3 Answers 3


I would definitely adjust the truing of the wheel. You don't want the wheel rubbing the brake; that will cause drag and wear on the brake and might cause problems (as in locking up the wheel) when braking. You also don't want to loosen the brake to prevent the rub, as that defeats the purpose of having brakes in the first place.

Note that I've had broken spokes often enough when commuting and touring that I carry a spoke tool in my kit for precisely this reason.

Based on my experience (which, in this at least, sadly is not minimal) I would add 1/4 turn of tension to the spokes ahead of and behind the broken spoke on the same side of the wheel, and take about the same amount of tension off the spokes ahead and behind on the opposite side of the wheel. You'll probably need to put on a bit more tension if it's on the drive side, take off less if it's on the non-drive side. (Note: this is based on a 36-spoke 3-cross wheel; if yours differs so will the required change.)

I tend to favour adding/removing tension by a fixed size movement instead of working to get the wheel completely true, since it's much easier to revert a constant amount of change when replacing the spoke. When you put the new spoke on, undo all your tension changes and you should be able to re-true the wheel using just the new spoke.

Obviously you're adding tension to some spokes, so the wheel won't be evenly tensioned; the idea here is to keep you moving long enough to get the spoke replaced. The adjacent spokes on the same side, and especially the trailing spoke, are substantially more likely to break. This is even more true on the drive side, where the power from the hub to the rim is primarily transmitted.

Your goal is to have a safe ride to the bike shop to buy a replacement spoke. :)

When you do replace the broken spoke, take the opportunity to inspect the adjacent spokes for damage and, if necessary, replace those too. It's vastly easier to do it once than have to do the same thing again the next day. And often there is an external cause for broken spokes, like chain damage, that can affect several spokes at once.

(There was one day on a trip when I walked the last 1/2km to a bike shop after the 3rd spoke in succession broke on the drive side of the rear wheel. Chain damage. Replaced those three and the next one too, was fine for the next 1000km.)

  • When my rear derailleur disappeared into my back wheel taking the chain with it, the spokes lasted about 150km before they started breaking; the chain left notches in 9 spokes. I replaced them 1 at a time, tensioning each one and starting with the 2 that actually broke. That maintained the dish, but the wheel needed minor but proper truing afterwards. I.e. your advice is sound, but it's worth paying attention to the cause (+1)
    – Chris H
    Commented Dec 11, 2019 at 20:49

No, you cannot true the wheel with a spoke missing - at least not as a permanent solution. I'd only do this to get home or to a bike shop if it was not a long ride.

Remember that spokes alternate coming from the drive (right) and non-drive side (left) of the hub, and a properly trued wheel balances tension from spokes from either side.

If you have a drive side spoke missing the two non drive side spokes on either side of its position will pull the rim toward the left, you would have to slacken these spokes because they are not pulling against the missing spoke. This is going to cause tension imbalances in the wheel which will stress other spokes and accelerate their failure.

  • 1
    This seems a bit overly dogmatic. Obviously a wheel isn't perfect with a missing spoke, but in most cases it is possible to make a typical aluminium rim + steel spokes wheel safe enough to ride to get to a bike shop.
    – DavidW
    Commented Dec 11, 2019 at 19:08
  • Agree with @DavidW that the first line is too dogmatic, but the answer addresses how running the wheel with -1 spokes will shorten the life of the others. I would presume the goal is to emphasize that this is not a good solution, and the OP needs to replace the spoke ASAP. I might add that if the OP is commuting with a load, I suspect the wheel will now be more likely to come out of true again if s/he hits a pothole or rough spot.
    – Weiwen Ng
    Commented Dec 11, 2019 at 19:21
  • 2
    It also depends how many spokes you have in the first place. A touring rim with 36 will be just fine with one missing, although of course you still want to replace it as soon as you can.
    – user68014
    Commented Dec 11, 2019 at 20:04
  • @user68014 my tourer was barely out of true with 2/9 drive side outer spokes broken. It would have needed a tweak for use with rim brakes set up tightly but I've got discs. 25km home with no more trouble, then i ordered replacements
    – Chris H
    Commented Dec 11, 2019 at 20:44

The damage from imbalanced tension is not going to be very much in the short term, i.e. less than hundred kilometres of riding. Especially if you don't pedal very hard but at a more leisurely pace.

But that said, I wouldn't bother adjusting spoke tension. You'll have to re-adjust again once you replace the missing spoke, and if you don't have proper equipment, it is more difficult to get it to correct tension if you need to adjust multiple spokes.

Instead, I would just adjust the brake cable to be a little looser, so that it doesn't rub. You'll still get some braking power, and rear brake is not so important for fast stops anyway.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.