I spent a lot of time trying to figure this out, so I thought I would post this to maybe save others the hassle.

The problem: Avid BB7 Calipers don't play nice with many of the popular Shimano Centerlock rotors.

  • The center spider on these rotors can extend so far that it fouls the little brass tabs at the base of the BB7 brake pads, especially if you're using the smallest, 160mm rotors. enter image description here

(True, you can cut those little tabs off easily enough, but that doesn't fix the 2nd problem.)

  • The broad center spider (there to increase stiffness and provide a heat sink) makes the rotor so stiff that it doesn't work well with the Avid BB7's single-side push design. It can't effectively shove the rotor from the outboard side toward the inboard pad, so you'll get poorer braking, uneven wear, and frequent pad replacement will be required.
  • IMHO, your money will be better spent keeping the rotors, and upgrading to a pair of hydraulic calipers. You can probably find a used set on ebay or pinkbike for the same cost as a new pair of rotors. They self adjust, they feel better, they modulate better... the list goes on. . I used to be intimidated by hydraulic because I didn't understand them. But now that I have experienced them, I would never go back.
    – Ben Stokes
    Commented Oct 26, 2020 at 17:06
  • 2
    I'm not interested in hydraulics, for many reasons. (They're not separable for a packable bike, as noted above, they don't generally come in lengths for the recumbents I ride, and I much prefer the simplicity of cable actuation for simple replacement in the middle of nowhere.)
    – user36575
    Commented Oct 27, 2020 at 1:30
  • @BenStokes For many that would mean new STI shifters, which are very expensive, if available for that goupset at all. Maybe WPNoviceCoder has a MTB but BB7s are found on many road and gravel bikes as well. Especially because of a later adoption of disc brakes in this sector in general. Commented Oct 27, 2020 at 7:35
  • My bad, ya'll. I am primarily a MTB guy, I am very familiar with the BB7, and because of it, I assumed this was a MTB situation.
    – Ben Stokes
    Commented Oct 27, 2020 at 16:04
  • No prob. If I were running regular uprights I'd go for those lower-end pre-fixed shimano hydros all day long. Mine are just funkier situations, plus the convenience of having only 1 type of spare pad needed for a whole bunch of bikes.
    – user36575
    Commented Oct 29, 2020 at 13:45

2 Answers 2


There are two different issues here; firstly the rotor width, and then the rotor spider.

I have a spreadsheet of all Shimano's disc brakes (excluding the 1970s models) here:


check the 'rotors' tab

Essentially the very first Shimano disc brake (post 1970s) in 1999 was made by Grimeca, and was part of the Deore XT M750 series; BR-M755. The Rotor was a six-bolt design called RT75. It was a hydraulic brake.

The next disc brake was the mechanical Deore M515, in 2000. I'm not really sure who made this, but it's a fairly generic design and uses pads that are used on Clarks and Tektro brakes. The same pads are still used on all low-end Shimano brakes today. This came out with RT50

Centerlock was first released in 2002 and was part of the XTR M960 series, hence RT96. There was now a Shimano-specific brake pad, which was narrower (in terms of how far they extend into the diameter of the rotor) than the generic ones used on the M515 etc.

enter image description here

cf. the generic pad used on M515 etc.

enter image description here

The rotor was still a fairly generic design:


enter image description here



enter image description here

The real change came with the release of XTR M975, in 2006, and RT97. The pad design did not change, but now Shimano was ready to release rotors that only worked with their 'narrow' pads. (the narrow pad design above was changed in 2010, to add support for fins)

enter image description here

And since a 'narrow' pad was standard, Shimano could use less steel for their braking track, and more carbon fibre spider or whatever, saving 10g for XTR users but making everyone else's life more difficult:

enter image description here

Anyway, since the early days Shimano insisted on making a cheap rotor out of non-hardened steel that would wear out quickly if used with sintered pads. The introduction of their new 'high-end narrow' vs 'low-end wide' rotors, pads, and calipers meant that they could eliminate the hardened rotors for the wide calipers. Hence the last such design was SM-RT63, released in 2005. All subsequent 'wide' rotors were non-hardened.

If one compares the SM-RT54 with SM-RT64

enter image description here

Then the braking track is 'wide'.

It seems to me that Shimano set out to create their own ecosystem, incompatible with anyone else's. The problem with SM-RT64 is that it might work with a given third-party brake given that it does not use any plastic parts near the braking surface, but given that the braking track is narrow, it might mean that the third party brake ends up doing something like this, but reversed (i.e. instead of the incomplete contact being on the outside of the rotor, you end up with it being on the inside of the rotor):

enter image description here

Therefore it seems that Shimano's 'narrow' brake rotors are probably best used only with Shimano's 'narrow' brake calipers.

Other than seeking out old rotors such as RT63, it strikes me that Shimano's cheaper rotors (anything numbered below '60' essentially) work just fine, and they are quite cheap, albeit that they should wear out quickly if used with a sintered pad.

Alternatively there are a number of third party centerlock rotors , such as Jagwire, TRP, SRAM 'Centerline', etc.

  • These spreadsheets of yours are impressive!
    – MaplePanda
    Commented Oct 27, 2020 at 5:41
  • The BB7s with the RT-64 do wear slightly down the arms. I'll edit original to show that.
    – user36575
    Commented Oct 27, 2020 at 17:35

What's needed is a Centerlock rotor with a spider small enough to clear the tabs as well as allow increased flexing of the rotor itself.

The simplest solution I've found is to use the Shimano SM-RT64 rotor, which has a smaller spider, flexes well enough, and is pretty inexpensive. It is also rated for metallic pads -- the standard with BB7s.

IIRC, these used to be "Deore" but now they're in the gravel line, "GRX." They can often be obtained for <$30 / rotor.

enter image description here


The SLX line SM RT-68 and SM RT-70 look like they'll also work, and they're also rated for metallic pads, but they cost about 2x. They weigh a bit less, so pick your priorities.

You could also look for Centerlock adapters (A Shimano one is available) to put a nice, flexy, ISO 6-screw rotor onto a Centerlock hub, but these adapters often cost as much as the SM RT-64 itself. I've read mixed reviews on their staying tight, etc., so I think forgoing the hassle and just buying a working rotor can be best.

A final alternative that solves both problems is to ditch the BB7s and go with TRP Spyres, which don't have the clearance issue, and they pinch the rotor from both sides. I actually did that on one bike, and the TRP calipers are nice, but they usually cost 2x BB7s. It's also a bit quicker to adjust a pad on a BB7 since you can use your fingers.


As noted in another answer, Centerline or TRP Centerlock rotors may work better and may fit the deep braking surface better. The depth of the Avid BB7 pads is enough to abrade the "leg" part of rotor in use, but this has not, to my knowledge, been a problem. (There's a thread here discussing it.)

This shows an SM RT-64 running with a BB7 caliper after about 3,000 miles, much of it pretty dirty.

enter image description here

You might suspect I'm missing out on braking power, given the deep pads and shorter rotor surface, but it's always been fine, and this is a heavy touring bike handling heavy loads.

This bike runs the same combo, a lot fewer miles.

enter image description here

One could also space these a bit further out with a washer under the fixing screw / alignment assemblies, but I've never felt the need.

  • These are very nice Q and A that are useful at least for myself as I rock BB7's on one of my bikes and will have to change discs eventually. While I use hubs with IS (6 holes) mounts, the problem with the disc spider clearance can also happen for them (not all IS discs are just plain stamped sheets of metal). I already have a trouble with BB7's and IS/PM adapters which make changing of pads a hassle (the adapter stands in the way of extracting one pad). Commented Oct 26, 2020 at 14:34
  • "You could also look for Centerlock adapters to put an ISO 5-screw rotor onto a Centerlock hub" — did you mean "6 screw" in this case? Or do I misunderstand what is meant here? Commented Oct 26, 2020 at 14:35
  • 1
    Fixed! Was getting confused on the count. (My Rohloff's got 4 screws on the rotor.)
    – user36575
    Commented Oct 27, 2020 at 1:28

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.