Bicycles Stack Exchange is a question and answer site for people who build and repair bicycles, people who train cycling, or commute on bicycles. It only takes a minute to sign up.
Sign up to join this community
I have these shifters and derailleurs:
front shifter Shimano ST-EF41, 3spd
front derailleur Shimano FD-TZ500, 3spd
rear shifter Shimano ST-EF41, 7spd
rear derailleur Shimano RD-TZ31, 7spd
I want to change my rear system with SRAM X5 rear derailleur (Long 9 -Speed) and SRAM PG-950 9 speed cassette(12-23 t).
The present Shimano has a freewheel whereas SRAM has cassette. What else will be needed?
If your goal is to convert your 3 gears in the front and 7 gears in the back to a 3 in the front and 9 in the rear this will be quite expensive. A new rear wheel will be required Your current rear wheel uses a screw on freewheel to mount the rear gearset. Nine speed rear wheels use a freehub mounting system with a cassette. You will need a 9 speed rear shifter and derailleur of the same brand, Shimano shifter with a Shimano derailleur or Sram derailleur with Sram shifter. You may need a new front derailleur, some 7 speed front derailleurs can be adjusted to work with narrower 9speed chains but it is trial and error and shifting may not be optimal. If you front shifter is a non indexed type this may actually improve shifting in this mismatch scenario. You will need a 9 speed chain. If you are doing these improvements yourself you will need to add the cost of a chain-tool, freewheel removal tool, cassette install/remove tool and a chaiin whip.
Might be shorter to list what you can keep:
You will need to buy or source replacement:
You should get away with leaving the front chainrings completely as-is, with the shimano shifter and front derailleur. As long as you're okay with visually-different shifters.
I've personally changed a 3x5 bike to run 3x9 deore and made no replacements to the chainrings or cranks, though I did have to modify the cage of the front mech to be a closer fit. And I have friction shifting on the front, for fine control across the range of gears.
If that doesn't work, you may also need
And then you might find the spacing between the chainrings has changed which will require
Do make sure the derailleur is rated for the cassette you intend to fit, AND that calculation includes the difference in tooth count between your large and small chainrings.
Reading between the lines you have a 3x7 bike with Tourney "groupset" so its unlikely to be a high or medium range bike. Tourney was the bottom shimano branded groupset, and while it does work, it is cheap.
So one might presume the rest of the bike is of similar specification and quality.
Be careful about throwing a lot of money at a bike in the form of upgrades. You might find that for "similar money" you can have a whole new bike with all the same components. This also leaves you with two bikes, not one and some scrap parts.
The 3x5 to 3x9 upgrade I did used an entire groupset salvaged from a bike that had suffered frame damage by being crashed and then driven over, but the car's wheels avoided the transmission. So if the parts are free then its feasible, but at new price it would have made no sense.
Those shimano shifters have integrated brake levers with long cable pull for V brakes. If you choose an integrated shifter/brake from SRAM then it will also have to be long-pull for your V brakes or cable-operated disks, whatever you have now.
You can also elect to fit separate shifters and brake levers instead of integrated ones.
This is a partial answer.
What else you will need: a rear shifter, your Shimano ST-EF41 will not be compatible with SRAM-X9 (as far as I know).
On the other hand, SRAM and Shimano 9-spd cassette/chains should be interchangeable, so if you can (virtually) upgrade your Tourney 7-spd to something 9-spd Shimano, you should be able to then replace this something 9-spd Shimano with the SRAM-X9.
