I sprayed WD40 on my disk rotor and now my rotor and pads are contaminated and now my rear brakes are practically useless.Is there any way to fix the problem without swapping out the brake pads and rotor ?


3 Answers 3


The rotor needs thorough degreasing, finishing with alcohol to ensure there is no residue. The trick is that when there's actual oil on it, you should use something nasty like brake cleaner, but then finish with alcohol. If it's really nasty another good way of getting the bulk of the contamination off is soak it in boiling water with some dish soap, then wipe/rinse, then finish with alcohol. That is a good way of getting all the millions of little holes cleaned out at once.

For the pads, there's not a guaranteed fix, but you can usually burn it out. Heat it slow and steady with a heat gun. Get it to smoke and then stop smoking. Test ride it in controlled circumstances to see how effective it was. There is some risk of ruining the bond with the back plate and have it fail in use, so it's at your own risk. Typically this works but it does take the right technique.

  • Would heating the pads until they smoke work with organic pads as well as it would with sintered? Commented Nov 7, 2021 at 19:02
  • 1
    @Lamarlatrell from what I've seen yes the compound isn't a problem, with the qualifier that it's always an experiment. Commented Nov 7, 2021 at 22:29
  • I've failed to burn oils off organic pads using a heat gun - the pads never got all their grip back and were horribly squealy. One set I heated from the back, the other from the pad face, and even after getting to smoking point repeatedly, and finally sanding the surface, they weren't good enough for more than a brief flat test ride.
    – Chris H
    Commented Nov 8, 2021 at 10:24
  • I wonder if the advice about the brake pads can actually be called safe. IMHO, every manufacturer states that brake pads after oil contamination must be replaced. And given the price for the brake pads, compared to the potential damage, i really would not recommend any other solution.
    – Burki
    Commented Nov 8, 2021 at 16:06
  • 2
    @Burki You are correct that it's not unequivocally safe. I have seen it work fine enough times that I do stand by what I wrote. I judge it to be worth discussing since many people are resource-constrained and all of us are capable of finding ourselves in a pinch. I also think it's true that once it's done and then test ridden, the remaining danger is mostly limited to the bond with the back plate failing in use, which is why I tried to be clear about that. Commented Nov 8, 2021 at 16:55

No sorry. You've contaminated the pads by braking while there is a contaminant on the rotor.

Had you cleaned the rotor before braking, the pads might have survived.

As it stands, your best solution is to remove the wheel, clean the rotor thoroughly with Isopropyl alcohol (especially between the rotor's spokes and in all the holes) and to replace your brake pads with new.

It may be possible to clean the brake pads by blotting, but in my experience that never works. Some people use heat to make oils drip out of pads, but again, that's never worked for me.

The only prevention is to be much more careful with overspray in the future. Use a piece of cardboard or rag/cloth to protect vulnerable parts. You can also not use aerosols and use drop bottles instead. There's no reason WD40 should be near a bicycle anyway.

  • 2
    One would want to heat the pads up to the point where the oil boils or burns off. I agree that replacement is far easier for simple pads. Fancy finned pads and the like may be worth a shot reviving.
    – MaplePanda
    Commented Nov 7, 2021 at 7:30

I can conform Criggie's experience that properly de-contaminating pads is a rather hopeless endeavour. You can get them to work again, but they won't have a proper, reliable, controllable bite – they only start screaming when you try to brake harder. To get your brakes to prime condition again, the only reliable thing is new pads.

What I found to be somewhat successful for the rear brake is to burn it out by its own power: select a properly steep fire road, 400 m with 100 m of elevation should do well. Ride it down at 10-15 km/h, while simultaneously braking (back brake only) and pedalling hard in a middle gear. That should bring the brake to smoking-hot temperature, you'll notice from that it will stop being responsive to changes in lever pressure. At that point halt (only then using the front brake) and quickly spray some water over the rear brake (this should cause steam sizzling).

I found that this self-cleaning made the brake work better afterwards than anything I could do with direct cleaning or heating, probably because it combines thermal and mechanical cleaning at the pad-rotor surface. And it's a low-effort solution (except for the climb before the descent, but that's just good training...)

  • This approach may be worth trying if (i) Only 1 brake is contaminated, not both as I had caused by a leaking bleed adaptor. (ii) You've got the perfect place for it, with a runout that would allow you to stop even if things go wrong, e.g. you can safely start going up the other side of a valley
    – Chris H
    Commented Nov 8, 2021 at 10:27
  • Wouldn't this method have a significant risk of quenching the rotor (well, a part of it), thus making it brittle and dangerous to use?
    – Wsal
    Commented Nov 9, 2021 at 16:48
  • @WaltoSalonen I don't think you need to worry about this. You may get a steel rotor to tempering temperatures, but that won't cause it to get brittle upon quenching. For that to happen, you'd need temperatures well above 400°C, but this is hardly possible with mere muscle and descent power – the rotor has too much surfact area. Even if you somehow achieve the necessary power, before you get to that point the pads would probably be on fire and the brake fluid gone, which also ensures no more friction heating is added. Commented Nov 9, 2021 at 19:43

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.