I always see professional bike builds have crimped ends on the cables. I've never been able to find any tools or ends to do that, so I just wrap the ends in electrical tape to keep them from fraying. I'd like to up my game and actually do it the right way but am failing at finding the correct tools and parts. What should I be searching for, and are there different sizes that I need to be aware of? All the cables on my current bikes seem to be the same size, but that's a relatively small sample size out of all the bikes (and cables) in the world!

  • 2
    I bought a pack of 50 for like $2 on AliExpress shipped to my mailbox.
    – MaplePanda
    Dec 8, 2021 at 7:58

3 Answers 3


They have a couple different names: cable tips and endcaps are common.

They come in two major sizes, one for 1.1 and 1.2mm shift cables and one for 1.6mm brake cable. In practice either of those two sizes can go on either cable type. Brake ones don't usually look very neat on shift cables. Some mechanics favor using the plain shift ones for everything, which is fine - they slide on kind of tight on brake cables, but (subjectively) look neat. When you see them for sale not specified shift or brake, it's usually kind of an in-betweener size, but I've also gotten bottles like that which were kind of too big to look good on shift.

In the days of "oversize" mountain bike brake cables, there were cable tips just for those. I believe they were borrowed wholesale from motorcycle applications.

To do the actual crimping, for many years I would just use light pressure on a blunt or low-quality cutter on a needlenose plier, i.e. keep a junky one around just for the purpose. As mentioned in comments, wire strippers also have a crimping part that can work. For a few years now I've been using the Park needlenose pliers that have a very effective crimper built in and are also good enough quality on their cutter to trim cables, so it's the fewest hand motions and slickest way of doing it that I know of.

Soldering the tips is a professional-level way of doing it as well. It's strictly better in a functional sense, but isn't done commonly anymore (that I've seen) because it takes longer. There have been times and places where it was the norm. Some people favor soldering and then capping the tips, but others argue for soldering and then leaving them bare because that approach maximizes their ability to be take out of their housings and put back through if needed. (Which it almost never is, but whatever). If you have soldering supplies but not tips, there's nothing wrong with doing it that way. When it's properly done it also eliminates any risk of getting poked a strand.

  • 1
    +1 for soldering: nice clean end, stick it in a tub of flux (by moving the tub!) then solder (with leaded solder, but the quantities are tiny) Dec 8, 2021 at 15:33

The ends are called crimps or ends. They are available in small handfuls for almost nothing to free at a LBS, or a virtual lifetime supply in a bottle for about $10. If you can't find them online, search for ferrules, which are the counterpart for cable housing. They'll all be categorized together, and ends should be nearby.

I've had this for probably 10 years and haven't even made a dent in it.

While you can use any study pliers to do the job, the Park CN-10 cable cutter has a crimper slot that's just the right size, specifically for the task.

Crunch that thing!

There really aren't different sizes of ends. While brake and derailleur cables do have differing sizes, they aren't different enough to make a difference when you smoosh an end on.

  • 2
    Cable ends do come in two sizes, for the home mechanic, brake cable ends gets the job done. Can also get ones that screw together so no need for a crimp and they are reusable.
    – mattnz
    Dec 8, 2021 at 2:08
  • Regular wire strippers have a crimping tool on them usually. If you don't want to buy a specialty tool.
    – Brad
    Dec 8, 2021 at 16:28
  • It's probably worth noting that these should probably not be confused with electrical ferrules, which are (very) thin-walled copper tube and NBG for preventing fraying etc. But the electronics industry does have a very nice range of crimping/swaging tools for this application. Dec 8, 2021 at 21:44
  • @MarkMorganLloyd few tools are more satisfying to use than a ratcheting crimp tool
    – llama
    Dec 8, 2021 at 22:16

Crimps are ideal, but there are three other good possible solutions, and a bad one.

  1. Solder, flux and heat. If you can get a small blob of electrical solder to wick into the braid of the cable, then that is an excellent place to cut the cable. It will leave the narrowest possible cable and the solder should stop the strands from peeling up. Downside is its sharp and can poke through skin fairly easily. Also, stainless steel, galvanizing, and chromed cables can make it hard to get wetting from the molten solder.

  2. Superglue/cyanoacrylate glue does a similar job to solder. Can be more blobby though.

  3. Heatshrink tubing is good - you slide on a short piece, heat it with hot air or a soldering iron, or even a lighter. The heatshrink shrinks under heat and conforms tightly to the outside of the cable. If I do this, I snip the heatshrink a few millimetres below the end of the wire, so it covers the exposed strands.

The most terrible option is to get the bike set up right, and then cut the flyaway end flush with the edge of the brake. This leaves you with a cable that can never be adjusted or reinstalled. However it is the most aero.
Opposite is to leave the entire length flapping in the breeze, risking it getting caught in the wheel or works in the brake/chain/derailleur.

  • 5
    The other terrible option is to never cut it and instead coil the excess up into a tight bundle Dec 8, 2021 at 2:31
  • 2
    An almost-okay-ish option is to not treat the end in any way and try to tuck it away to avoid getting caught on it.
    – Michael
    Dec 8, 2021 at 7:55
  • 3
    If you ever caught an unprotected end in your flesh, you'll know why proper end-capping is essential.
    – Carel
    Dec 8, 2021 at 8:18
  • @Michael yes, but I find the end strands will un-lay themselves over time. There is a definite art to making the fly end tuck into something... down the side of a V brake spring was common.
    – Criggie
    Dec 8, 2021 at 10:56

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.