All Questions
Tagged with derailleur cable
18 questions
1
vote
1
answer
156
views
New shift cable damaged after clamping to shifter
I just replaced all the cables and housing on my bike and was annoyed to discover on close inspection that the front derailleur cable has sustained some damage from the cable clamp on the derailleur:
...
6
votes
1
answer
1k
views
Shifter cable broke in the shifter and now the end is stuck in the shifter
So The end of my rear derailleur shifter cable is stuck in the shifter. Is it even possible to get out? See the picture below. Shifting up and down doesn't really do anything to its position.
Edit: I ...
12
votes
6
answers
3k
views
Ultegra RD-R8000 derailleur chewing up shifter cable - WTH?
I have an Ultegra RD-R8000 (GS cage) that has chewed up multiple shifter cables (Dura Ace and Jagwire) at the cable bolt. Seems that when in a high gear (11t chainring) the cable bends over the clamp ...
4
votes
1
answer
919
views
Front derailleur cable touching frame?
Installing gears on my bike on my own for the first time.
I pulled the front derailleur gear cable through an intended hole in the frame like so:
So everything should be fine. However, looking under ...
12
votes
3
answers
4k
views
Why do I constantly have to re-index gears?
I've got a road bike with a high end 11 speed groupset that is about 3 years / 30,000 km old. Chain and cassette have both been replaced recently (i.e. 500 km ago).
What I'm experiencing is a constant ...
2
votes
1
answer
2k
views
Shimano RD-R7000 cable cut into thread?
That gap/cut in the hollow screw of the cable mount is not supposed
to be there, right?
If so, is this a typical defect?
The hollow screw is pressed into the derailleur
body and not replaceable, so ...
3
votes
3
answers
1k
views
Shift lever tight when cable clamped in derailleur, adjustments seem futile
I have a 2020 Giant Trance 2 I purchased new at the beginning of June 2020. Recently I had to replace my shifter cable (I broke a ferrule and the cable was fraying and very short, so I figured the ...
4
votes
4
answers
1k
views
Front derailleur cable hits path of pedal
The front derailleur cable is on the path of the pedal.
Derailleur cable is in the path of the pedal (right of picture):
The amateurish solution of pulling it back with a loop requires a solution ...
2
votes
1
answer
240
views
Seating the rear derailleur cable housing
Unpacked road bike. Assembly is simple enough, except that the rear derailleur cable housing is not in its groove (I'm sure there is a specific term).
Here is a picture.
No matter how much I tug (...
1
vote
2
answers
12k
views
Front derailleur cable suddenly very slack (no shifting), not sure what's caused it
I last rode the bike on Sunday. Throughout the ride I noticed the front shifter (grip friction shift, Shimano) was feeling "looser" than normal (hard to describe, it didn't feel "right" and seemed to ...
1
vote
3
answers
326
views
How do I thread rear derailleur cable through this adjuster?
this is a Lemond Zurich from around 1999 that I'm converting to 10 speed in rear. I can't get the cable to thread past this metal part that seems to be a fine adjustment for rear derailleur. I can't ...
1
vote
2
answers
164
views
New Cable Anchor Bolt for SunTour Accushift Edge
I got a pretty good condition Trek 400 and it has SunTour Edge components. Unfortunately, the rear Accushift derailleur is missing a cable anchor bolt so I have no way of attaching a cable to it. Are ...
0
votes
0
answers
59
views
Gear change sticking only on specific changes - cable issue? [duplicate]
I'm riding a hybrid with 48/36/26 chain ring and 9 speed 11-32 cassette.
When I change up OR down at a specific point the shift is slow and doesn't always engage. On the 48 this is between the 21 ...
3
votes
2
answers
236
views
How to replace derailleur cable housing?
My derailleur cable housing (sheath) has exploded:
I bought a new sheath of the exact same length:
PROBLEM: Now I realize that unlike brake cables that are like []------, derailleur cables seem to ...
5
votes
2
answers
4k
views
How to adjust cable length on integrated brake/shift levers, when there is no barrel adjuster?
I feel bad asking this question because I've been doing bicycle maintenance for over 20 years and this seems like a noob question. I was unable to find a Shimano manual to answer this question. I ...
19
votes
3
answers
13k
views
Is it normal for my derailleur cables to cross over on the down tube?
I've just picked myself up a Specialized Allez Sport 2014 road bike from Evans Cycles (UK).
I test rode the bike and I'm happy with the bike, but when I got home, and flipped the bike over to make a ...
1
vote
1
answer
404
views
Front derailleur cable change
I changed my shifters and need to change my front derailleur cable.
I just don't know how to proceed exactly.
A guide I found told me to:
on big sprocket, small plate (is that the english word?? ;p)...
6
votes
3
answers
8k
views
Why does my bike stick in low gears?
When I change into a low gear (i.e. onto a bigger cog) on my back cog all is fine. However, when I later change up again the chain sticks on the larger cog. I commute about 10 miles a day and this has ...