3

I am having a new MTB Montra Rock 1.0D 2016.

When I ride my cycle, for first 5 to 10 minutes, I hear a tick sound on every pedal when my pedal is at 3'o clock to 6'o clock position on my right foot.

After few minutes, no noise at all and everything is quiet and smooth.

Next day, same happens for first few minutes.

I couldn't figure out source of the tick.

Also to note that, when cycle is standstill, no tick sound at all when moving pedal with hand, not for few minutes also, means no tick at all and thats what I want.

If i ride cycle, then only I hear tick for first few minutes

Can anyone help me?

UPDATE

BIKE SPECIFICATION

Improve this question
9
  • Have you tried a different pair of pedals?
    – Batman
    Commented Oct 15, 2016 at 13:46
  • No, the original one only.
    – Hemal
    Commented Oct 15, 2016 at 13:47
  • 1
    There are some other questions that duplicate this, but I can't find them just now. Possible causes are bad pedals, pedals not screwed into the crank arms properly, crank arms not tightly fastened to crank shaft, chain rings not tightly fastened to crank spider, bad crank bearings, crank bearings loose in the BB. Of these, having the crank arms not properly fastened to the shaft is all too common and rapidly leads to destruction of the arms and crank. The others are less concerning (though annoying).
    – Daniel R Hicks
    Commented Oct 15, 2016 at 20:43
  • 1
    @Hemal You're not correct. First, the top half of the chain (the part that runs through the derailleur) is under tension when pedaling, so it can't wobble around. Second, I can't see any mechanism that would cause the chain to get shorter after using it for a bit.
    – David Richerby
    Commented Oct 17, 2016 at 7:37
  • 1
    first and easiest step is to grease the pedal threads - this was the solution for me when i had similar problem
    – Andy P
    Commented Oct 17, 2016 at 8:11

4 Answers 4

Reset to default
1

I had the exact same issue on my bike last year. Drove me crazy. Only happened when pedaling and rate of clicks depended on cadence, was not changed by gears. Turned out to be slightly dry/loose pedal threads, i.e. where the pedal spindle threads into the crank arm, not the inernal bearings of the pedal itself:

enter image description here

Try this: remove the pedals, clean the threads with an old rag, apply a small amount of grease to the threads. Put them back in and tighten up quite firmly. See if clicking disappears. I find I have to do that every 2-4,000 km or so.

Don't forget left pedal is threaded the opposite of "normal".

Improve this answer
3
  • Will try this and let you know.
    – Hemal
    Commented Oct 18, 2016 at 4:49
  • 1
    I tried removing right pedal and removed it from crank. Then I reattached it without any greasing and noise is gone. Thank you.
    – Hemal
    Commented Oct 21, 2016 at 7:33
  • 1
    No problem. FYI: typically you should apply a small amount of grease to the threads before installing or reinstalling a pedal. This is so it is easy to remove at a later date. Note that the pedals are threaded such that when you are pedalling, the rotation applied to the threads is a tightening one, so you don't have to worry that the pedal is going to work itself loose if you grease it.
    – SSilk
    Commented Oct 24, 2016 at 16:55
1

Possible cause:

Without any further knowledge about your bike, I'd guess that the clicking noise has something to make with a grease in either the pedal or the crank bearings. (As you mentioned that the sound occurs only when the pedals are in the very same position and when you actually put some force on them, I'd say it isn't caused by something like an unevenly tightend handle bar or loose seat post etc etc..)

Since you only hear the clicks within the first 5 - 10 min when riding, I assume this is the time the grease needs to "warm up", as in become slightly more fluid due to the friction it experiences. During this time some of the little balls inside the bearings could cause the clicking noises.

Possible solution:

  • Make sure that the pedal bearings arent tightend too much (in case you can open them at all).
  • check on your cranks, whether they're tightend properly
  • check on the more unlikely sources for the click (i.e. seat post, saddle, etc.)
  • replace bottom bracket

I'd also advice you to do these steps iteratively, so you get to know the source of the problem.

Improve this answer
2
  • Sure, will look into this and will let you know.
    – Hemal
    Commented Oct 17, 2016 at 6:15
  • But if there is a problem with rear hub or bottom bracket, why the noise is not coming when cycle is standstill/on trainer/on stand?Noise appears when I am on the cycle riding.
    – Hemal
    Commented Oct 18, 2016 at 4:48
1

If it's not your pedals or bottom bracket, as covered by dru87's answer, it's your rear hub: that was the cause of a similar noise on my own bike a couple of months ago. The reason it only happens at a particular point in your pedal stroke is that that's when you're pushing hardest; the reason it goes away after a few minutes is, as in dru's answer, that there's not enough lubricating grease but, after a little while it's warmed up enough to flow more and cover the whole bearing.

Improve this answer
6
  • May I know how do I get rid off this?
    – Hemal
    Commented Oct 17, 2016 at 13:08
  • I would expect some correlation between front derailleur gear and frequency of clicking in this case unless it's a single speed or 1x drivetrain which it is not.
    – SSilk
    Commented Oct 17, 2016 at 17:05
  • @SSilk When I had a creak caused by a rear hub problem, it was once per rotation of the pedals.
    – David Richerby
    Commented Oct 17, 2016 at 17:14
  • But if there is a problem with rear hub or bottom bracket, why the noise is not coming when cycle is standstill/on trainer/on stand?Noise appears when I am on the cycle riding.
    – Hemal
    Commented Oct 18, 2016 at 4:48
  • @Hemal Because the noise is caused by the strain of you pedalling. When you pedal, you exert a force that's a decent fraction of your weight, which is multiplied by the lever arm of the crank and chainring.
    – David Richerby
    Commented Oct 18, 2016 at 8:26
1

It could also be your crank hitting the crimp cap for the front derailleur cable, check if your cable is sticking out a little bit.

Improve this answer
1
  • Checked it, not a problem
    – Hemal
    Commented Oct 18, 2016 at 4:48

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.