Questions tagged [chainring]

The cogs (gears) at the front of your drive chain, connected to the cranks.

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
123 views

5 arm cranksets versus 4. Which is better and why?

I'm looking to buy a Sora triple crankset. Shimano make two types one has 5 arms and the other only has 4 arms. Which should I get and why would that be a better choice? I'm a slow-ish rider. I'm 50 ...
2
votes
1answer
1k views

What is required for a proper boost chainline on a 1x drivetrain - only a boost chainring or an entire crankset?

To obtain a proper chainline for a boost rear hub (~52 mm), is it enough to fit a boost (3 mm offset) chainring to a 1x crankset which is originally non-boost, or is an entire boost crankset required (...
2
votes
0answers
101 views

Nasty noise from chain device

Hi I've purchased and fitted a superstar components plasma chain device in my specialized big hit. It makes a terrible noise and I really don't see why. As far as I can see I've set it up correctly ...
2
votes
0answers
827 views

Is Shimano 36/24 double crankset possible?

I'd want to exchange my triple crankset with double. After playing with gear calculator and testing some double setups, I came to the conclusion I need 36/24 gearing. I have 10 speed drive, so I'm ...
2
votes
0answers
178 views

Where should I look for a reliable chainguide for a large chainring (52T)?

I'm building a hybrid bicycle using a Specialized StumpJumper S-Works carbon frameset. The drive-train is 1x12. Wolf Tooth 52T cyclocross chainring, to beef up the top end gearing. (The chainring ...
2
votes
0answers
93 views

Chain vs seatstay with a 50T Chainring - BMX frame

I plan to put a 50T chainring on my bmx but I am afraid to have an interference between the chain and the frame. Does anybody know what is the critical distance between the seatstay and the chain so ...
1
vote
0answers
59 views

Modify a front derailleur cage to allow for non-round chainrings like Biopace or Rotor?

I am repairing my road bike after a mishap where it swallowed the rear derailleur around the cassette and into the front derailleur. As part of the rebuild, I'm swapping out the badly worn old ...
1
vote
1answer
115 views

SRAM AXS double to single

I'm looking at a road bike with SRAM Force AXS 2x crank but would like it as 1x. I see from photos that the spider is separate from the right crank. Are the 1x vs 2x arms and/or spiders different? ...
1
vote
0answers
100 views

chain / cassette / chainrings replacement ratios - how often to you usually replace cassettes & chainrings per number of replaced chains?

I'm looking to get other riders experiences with how often cassettes and chainrings usually have to be replaced per the number of chain replacements. On my 2 road bikes I usually find roughly the ...
1
vote
0answers
72 views

Will removing extra chainring mess with chain alignment?

I have a folding bike with 1x6 speed. I plan on making it a 1x9. I saw this crank set and cassette, 3x9 speed, for a fairly cheap amount and was thinking of getting them and installing on my bike. If ...
1
vote
0answers
410 views

Low gearing setup for road bike with Shimano dual control

Question: What is my best bet for a crankset, given the following requirements for a road bike I am setting up: 68mm "English" thread bottom bracket Shimano STI "brifters", 2x10 (I already have ...
0
votes
0answers
25 views

Qring with Etap shifting problem

I switch to Qring with my Etap Quarq crank. I cut it big qring for fit (Quarq was on the way) and switch to a new chainring bolt for hidden bolt. the problem I have now is when I’m shifting from the ...
0
votes
0answers
135 views

Ultegra FC-R8000 Chainring Bolt Fatigue

As per my troubleshooting to find a bike creak (Ultegra FC-R8000 Right Crank Arm Creak) - I have installed and removed the same chainring bolts ~8 times. In the process I snapped one of them. Each of ...
0
votes
0answers
41 views

Does anyone here have measurements of SRAM's direct-mount spline interface?

The makerspace I work in purchased a new metal milling unit and I want to test its software's tolerances and mill a narrow-wide chainring. I'm guessing it just consists of a circle with square ...
0
votes
0answers
2k views

Replacement crankset for Shimano SG B 52/39?

I have a very basic Specialized Allez (XL frame) street bike (pictured in my avatar) with a cheap SG B52/39 chainring needing replacement (warped and wearing out after two years of daily use). But ...